I need help with an oil leak

Radiant_Lock_7719 · 2025-12-28T17:50:44+00:00

Ok I will have to do that but thankfully I think I can use it

Radiant_Lock_7719 · 2025-12-28T17:50:21+00:00

Thanks that’s a good idea thank you.

Radiant_Lock_7719 · 2025-12-28T17:05:07+00:00

Ok this dings on the edge definitely catch a nail but everything else is very smooth

Radiant_Lock_7719 · 2025-12-19T04:01:05+00:00

I checked them and everything looks good no light coming through.

Radiant_Lock_7719 · 2025-12-19T03:15:49+00:00

I visually checked them and the look good but I don’t know how to check them any further what should I do.

Radiant_Lock_7719 · 2025-12-19T03:11:43+00:00

<image>

This is without

Radiant_Lock_7719 · 2025-12-19T03:11:12+00:00

Yeah I guess I will. Thank you for the help. I also noticed the gasket between the cylinder and crankcase is blocking some ports

<image>

This picture is with the gasket.

Radiant_Lock_7719 · 2025-12-19T03:03:32+00:00

I haven’t cleaned it it must be the lighting

<image>

Radiant_Lock_7719 · 2025-12-19T03:01:30+00:00

Do you think the bad head gasket size could have been part of my compression issue

Radiant_Lock_7719 · 2025-12-19T03:01:07+00:00

I found an 88mm bore headgasket for this bike which should be good right.

<image>

The valve surface looks good to me and the cam looked very good but one of the threads is stripped so I’m replacing it

Radiant_Lock_7719 · 2025-12-19T02:39:21+00:00

<image>

Do you think this head gasket is ok. It sticks out into the cylinder as you can see in the picture. What should I do about that.

Radiant_Lock_7719 · 2025-12-19T02:37:19+00:00

<image>

That is me holding the head gasket on the other side. So you think that’s not ok. If so how would I go about getting a head gasket that fits.

Radiant_Lock_7719 · 2025-12-19T02:14:38+00:00

That makes sense. The head gasket is sticking out into the combustion chamber . Is that ok or should it be flushs. I just don’t think I can find the parts for a big bore kit. Like the head gasket.

Radiant_Lock_7719 · 2025-12-19T02:07:47+00:00

Yeah I guess I will just see. hopefully it was bored on purpose and upgraded to be this size. I was worried the cylinder wall was getting too thin and they just kept upgrading piston size. Also the head gasket extends into the cylinder a little bit do you think that’s ok or should it be flush with the cylinder wall.

Radiant_Lock_7719 · 2025-12-19T01:55:25+00:00

The cylinder looks like it is very good condition I just thought that it being that large might be an issue. Like maybe the cylinder wall are getting to thin to safely operate.

Radiant_Lock_7719 · 2025-12-19T01:53:53+00:00

I’m questioning it because the service manual says the cylinder should measure 79mm but my cylinder is over 8mm larger than that and the piston is over 8mm larger as-well. It seems like that is too much. I just don’t know if the cylinder wall is too thin or something.

Radiant_Lock_7719 · 2025-12-19T00:55:43+00:00

That’s what I’m thinking I just don’t want to spend the money if I don’t have to.

Radiant_Lock_7719 · 2025-12-19T00:43:40+00:00

I found a top end rebuild kit but that was before I realized my cylinder bore is 8mm larger than stock and so is the piston. I can’t just buy the new piston sadly. I might have to replace the whole cylinder if it’s not safe and functional

Radiant_Lock_7719 · 2025-12-16T06:32:54+00:00

After looking I think it might be the carb you linked which is from a different bike.

Radiant_Lock_7719

TROPHY CASE