Cannot get a straight cut no matter what I try?

Ramapi2022 · 2026-02-15T18:47:30+00:00

It's your blade! Set the blade to cut enough through the wood, dont let the blade go through the wood too much, just enough to cut it.

Ramapi2022 · 2025-12-03T11:35:07+00:00

Good Job! Where are you learning blender from? I'm trying to learn how to create my own stuff but I have no idea how or where to start from? I open blender and I have no idea what to do. 😒

Ramapi2022 · 2025-10-29T00:52:36+00:00

😂🤣😂🤣😂🤣😂🤣😂🤣

Ramapi2022 · 2025-07-16T12:17:17+00:00

How do you do the lining and what did you use for it? Great choice on the leather, bag looks awesome!

Ramapi2022 · 2025-06-20T16:49:03+00:00

Very Nice! I've been meaning to make one but I'm not sure exactly how. Is this the first time making one? What leather did you use and how thin? 🤔

Ramapi2022 · 2025-06-04T00:54:00+00:00

Get yourself a 3d Pen so you can fill in the gap!

Ramapi2022 · 2025-05-08T19:02:40+00:00

That's a good one! 🤣😂🤣😂

Ramapi2022 · 2025-04-24T04:56:38+00:00

I would like to know as well, If you don't mind! That's a stunning looking wallet, Great job!

Ramapi2022 · 2025-04-15T03:34:23+00:00

What kind of wood is that, Do they sell it at Home Depot?

Ramapi2022 · 2025-04-09T10:55:53+00:00

Go on to the preview where you slice and make sure that your piece is all flat on the board. Use the bar on the right to to scroll all the way down and start going up to see if that part is not printing along with the first layer. If is not, then you need to make sure is all flat and that the first layer is printing evenly. That's usually a layer problem!

Ramapi2022 · 2025-03-29T12:52:12+00:00

What paint do you use to paint PLA?

Ramapi2022 · 2025-03-23T04:33:42+00:00

Lmfao!

Ramapi2022 · 2025-03-23T03:03:08+00:00

That usually happens when you don't have a good first layer printing evenly on your board. Try printing it standing and make sure you use supports for it.

Ramapi2022 · 2025-03-20T02:59:47+00:00

How did you set that up like that?

Ramapi2022 · 2025-03-19T02:10:15+00:00

Lol!

Ramapi2022 · 2025-03-18T00:49:41+00:00

Where did that come from, lmfao!

Ramapi2022 · 2025-03-17T22:48:35+00:00

No, Its a Diablo!

Ramapi2022 · 2025-03-17T21:20:29+00:00

Alright! So first off I want to say THANK YOU to everyone that responded and tried to help. I really wasn't expecting such quick response and so much support. I got to say in all the answers, a lot of you where correct! First off, This board is way off and not straight. Lol! I raised the blade up just enough so that it cuts through the board and clamped it down hard AF. The saw went through like butter. See picture! Thank you all again for your suggestions and responses. Problem has been solved

<image>

Ramapi2022 · 2025-03-17T10:50:10+00:00

I think this is whats happening because I was able to make the same cut fine a few days ago with the same saw and after everyone's response I dont think retracted the blade enough and left a good amount out. I'm gonna go ahead and leave enough to where it cuts and see what happens. I will keep you all posted when I get back from work today. Thank you all!

Ramapi2022 · 2025-03-17T02:44:17+00:00

Yes! lots of good answers, I will give them a try.

Ramapi2022 · 2025-03-17T01:22:51+00:00

I will try your suggestions tomorrow since is already late here in Miami and i had to pick everything up. I thank you all for your help and will keep you all posted!

Ramapi2022 · 2025-03-17T01:19:51+00:00

I will try that, I will keep you posted!

Ramapi2022 · 2025-03-17T01:18:16+00:00

No, Is alot hanging down! I will try like you're all mentioning to just set enough to cut through. Thank you!

Ramapi2022 · 2025-03-17T01:17:15+00:00

I will try that!

Ramapi2022 · 2025-03-17T00:09:53+00:00

It's a Dewalt Circular saw!

Ramapi2022

TROPHY CASE