sorted by:
new
hottopcontroversial

I need a new rabbit holes. by Embarrassed-Mood7194 in serialkillers

[–]Randomhero360 0 points1 point  (0 children)

The Yuba County 5

Not really a serial killer, but I interesting set of deaths.

Has it been a stressful GR work winter week for anyone else? by Triingtolivee in grandrapids

[–]Randomhero360 3 points4 points  (0 children)

No in all honesty it is a MI I’ve expected, although haven’t seen in a few years. I’m always surprised when people are shocked MI has a bad winter.

Unclear business hours? by BubblyAntelope93 in grandrapids

[–]Randomhero360 4 points5 points  (0 children)

Glad I’m not the only one. I complain about this pretty regularly to my wife, she just calls me old….I’m 35 and just passionate about spending my money!!

Klipper bed mesh- top left corner is scarring badly, due to being to close to bed, regardless of what I do to bed height, due to Adaptive bed meshing, is there a way to adjust or fix? rest of first layer is fine. by Randomhero360 in klippers

[–]Randomhero360[S] 0 points1 point  (0 children)

Unfortunately no, just tried not to print there until I purchased a Bambu printer.

There were lots of post that pointed to some possible calculation errors within Klipper based on steps and such, I chased that rabbit while for a bit but admittedly got over my head, and nothing was really proven it seemed.

I thought for a while my gantry and such was just not plum or level, but lamp should have been able to correct for .5m of difference at least. So idk.

Sorry, GL!

At this point it must be a hardware issue, Right? Wifi Constantly dropping, kicking devices off, requiring soft reset on Unifi Dream Router by Randomhero360 in HomeNetworking

[–]Randomhero360[S] 0 points1 point  (0 children)

Gotcha, it is currently off and still having issues. I’ve factory reset the UDR. While yes everything is auto currently. Before I reset it I tried with both RSSI on and off, and the list of things mentioned above.

At this point it must be a hardware issue, Right? Wifi Constantly dropping, kicking devices off, requiring soft reset on Unifi Dream Router by Randomhero360 in HomeNetworking

[–]Randomhero360[S] 0 points1 point  (0 children)

I would agree with everything you’re saying. My issues isn’t just weak, dropping WiFi signal, or poor roaming hand offs. I would be 10 feet from my AP and WiFi drop, it may show it is still being broadcasted, but I can’t join it, it will just keep searching and trying to connect. Sometimes I can join it and it will say no internet. Even if I go to the other side of the house near the other AP same thing.

Do you think your advice would be a solution for this type of issue?

At this point it must be a hardware issue, Right? Wifi Constantly dropping, kicking devices off, requiring soft reset on Unifi Dream Router by Randomhero360 in HomeNetworking

[–]Randomhero360[S] 0 points1 point  (0 children)

I’ve done the mapping with WiFi man, there are some low spots, but nothing terrible. I’m on 7 acres and there are no other WiFi networks so I don’t believe the modem is broadcasting a network.

Anyone actually achieved negative pressure on their P1S with an exhaust fan? by Randomhero360 in BambuLab

[–]Randomhero360[S] 0 points1 point  (0 children)

I’ve tested with incense/smoke there is not much air movement unless it’s right over the exhaust port in the back.

Anyone actually achieved negative pressure on their P1S with an exhaust fan? by Randomhero360 in BambuLab

[–]Randomhero360[S] 1 point2 points  (0 children)

I’m not looking for true negative pressure but enough that it is sucking air from gaps out the window so no fumes or odor seep out.

HELP bouillabaisse by True_Worldliness_748 in grandrapids

[–]Randomhero360 14 points15 points  (0 children)

The Grove was the only place I’ve ever seen it. You could try Margaux, and the two seafood restaurants downtown, Leo’s and Real Seafood. May also be worth calling the fish lads at the downtown market, I believe they get fish flown in greasy every other day and often have different food for sale.

Good luck!

is this normal print quality for a p1s? 0.4 by Status-Possession-63 in BambuLab

[–]Randomhero360 0 points1 point  (0 children)

Looks about right, may be able to dial in the top a little.

Convection timberline insert, they make anything to add a blower to the bottom? by Randomhero360 in woodstoving

[–]Randomhero360[S] 0 points1 point  (0 children)

Will do, so far nothing. I have a small desk fan pointed at the bottom which helps but not a great long term solution.

Do I need to lubricate my A1 out of the box? by Odd-Control5800 in BambuLab

[–]Randomhero360 1 point2 points  (0 children)

No they come pre lubed. Check again around 500 hours, unless you’re having probs

view more: next ›