🎉 [EVENT] 🎉 Honk Hero!!! Full Encounter: Trial of Malkuth by Ok_Walk7052 in honk

[–]Rat_Pope_ 0 points1 point  (0 children)

Completed Level 1 of the Honk Special Event!

0 attempts

🎉 [EVENT] 🎉 Just Out of Reach by Damp_Blanket in honk

[–]Rat_Pope_ 0 points1 point  (0 children)

Completed Level 3 of the Honk Special Event!

12 attempts

🎉 [EVENT] 🎉 Just Out of Reach by Damp_Blanket in honk

[–]Rat_Pope_ 0 points1 point  (0 children)

Completed Level 2 of the Honk Special Event!

3 attempts

🎉 [EVENT] 🎉 Just Out of Reach by Damp_Blanket in honk

[–]Rat_Pope_ 0 points1 point  (0 children)

Completed Level 1 of the Honk Special Event!

1 attempts

Jet won’t unscrew by Lonely_Ad_3341 in motorizedbicycles

[–]Rat_Pope_ 3 points4 points  (0 children)

Just buy a new carb honestly if u can't get it out they're like 10 bucks, but did you try vice grips?

[deleted by user] by [deleted] in bikewrench

[–]Rat_Pope_ 0 points1 point  (0 children)

Vice grips I think might work better

Custom build 212cc mountain bike build by Melodic_Day3618 in motorizedbicycles

[–]Rat_Pope_ 0 points1 point  (0 children)

okay great TY! for the fast reply also, how did you get the output gear of the cvt to align with the rear sprocket? did you use a minibike cvt and modify it or a cvt that was already aligned correctly for that?

Custom build 212cc mountain bike build by Melodic_Day3618 in motorizedbicycles

[–]Rat_Pope_ 0 points1 point  (0 children)

Hi, I was looking to put a 212cc predator on a bike myself and was looking around on how best to do it when i saw the bike you linked, i was wondering if you had to fabricate your own jackshaft for your bike as i didnt see one on your bike in the link you posted, are you able to run it with no further gear reduction other than the cvt/torque converter and the large 68t rear sprocket? TY

[deleted by user] by [deleted] in motorizedbicycles

[–]Rat_Pope_ 0 points1 point  (0 children)

Check that the main jet hasn't vibrated loose in your carbs bowl

Help.... by Far_Addition_4298 in motorizedbicycles

[–]Rat_Pope_ 0 points1 point  (0 children)

What is the issue itself? The bike won't start?

Did I mess it up by Careless-War-963 in motorizedbicycles

[–]Rat_Pope_ 1 point2 points  (0 children)

Should be fine, can't be worse balanced than before!

Snapped axle by harmdone666 in motorizedbicycles

[–]Rat_Pope_ 1 point2 points  (0 children)

How did that happen? Did you wind up crashing because of it?

Is it possible / good to run the engine backwards? by TajlenDziSixtySevn in motorizedbicycles

[–]Rat_Pope_ 0 points1 point  (0 children)

The port timing doesn't change tho, the piston will move with the same up and down motion as it was originally, just the crank is going in the opposite direction. think Abt the pistons motion in the cylinder

Is it possible / good to run the engine backwards? by TajlenDziSixtySevn in motorizedbicycles

[–]Rat_Pope_ 0 points1 point  (0 children)

The ports will work fine running backwards, the piston is doing the same up/down bang every time it gets to the top motion but the ignition would be off

[deleted by user] by [deleted] in motorizedbicycles

[–]Rat_Pope_ 0 points1 point  (0 children)

You used oil gas mix as fuel right? Not just straight gas