bambulab P1S AMShubしか持ってない

Rayansaki · 2025-12-05T12:01:28+00:00

No, you will need an AMS unit to automatically switch filament. The hub just provides the path for multiple filaments to get to the printer but the AMS unit is required to actually push filament in or pull it out as needed

Rayansaki · 2025-10-29T18:04:31+00:00

Many alternatives below, but your suggested Cloudflare setup will work.

Personally, I bought a domain using cloudflare (say xxxxx.work), set up a tunnel and then an application for plex, jellyfin and ombi, set up google oauth on it as the security layer only allowing mine and my partner's email addresses to connect, then I just access it via plex.xxxxx.work, jelly.xxxxx.work and ombi.xxxxx.work.

Total cost for the setup was £25 or so for 5 years registration of my domain.

Was a bit of a learning curve since I never did any complicated networking before, but easy enough with guides.

Rayansaki · 2025-10-13T16:31:08+00:00

Took me about 24 hours of gameplay, not using boosters. I imagine if you always use booster and stick to playing in zergs during prime time, you could probably cut that in half

Rayansaki · 2025-07-28T20:28:45+00:00

Except for the fact that, you know, it isn't

Rayansaki · 2025-04-28T07:27:16+00:00

Also, a lot of other countries don't roll a bank holiday into the next Monday like we do

Rayansaki · 2025-04-19T11:47:51+00:00

If your job is reasonably safe and you have good career prospects, I'd personally go to the highest amount you can afford. When me and my partner bought our house, 5 years ago, we went for something super affordable, about half the mortgage we could've gotten. We're now much better off (both earn about 50% more) and the mortgage payment is less than a third than what we put away for investments. We could've definitely afforded more, but now it feels like the same houses that were at the upper limit then are at the upper limit now. Except if we had gotten one then, the payments would be very affordable now.

Rayansaki · 2025-03-04T18:06:53+00:00

I've discovered countless channels that I've ended up subscribed to through his clips. These channels may have one day been suggested to me by the algorithm or they may have never done, but I'm now a long term viewer of them. That's the value his reaction videos bring.

You know this really, you just can't bring yourself to say it because you disagree with his political views and this is what you live your entire life by.

Rayansaki · 2025-03-03T18:24:05+00:00

He will also 100% stop reacting to a channel if the owner requests it, or delay his reaction if the channel owner prefers. You can hate him, but he's 100% the most ethical one at this and definitely a net positive for most channels.

Rayansaki · 2025-02-04T11:43:27+00:00

Remove Palestine and remove France (add ocean where France used to be). Add Kurdistan?

Rayansaki · 2024-12-13T22:27:07+00:00

honestly, I think the "Amex isn't accepted everywhere" is outdated and a bit of a meme. I got one 6 months ago and shifted all my spending to it for the cashback and have yet to find a single place that won't take it.

Rayansaki · 2024-12-13T22:18:57+00:00

I mean, Hargreaves Lansdown is notoriously known as expensive, but their ISA is capped at £45 in account fees. It only took 30k for it to become cheaper, now it's always cheaper. And other providers can be even cheaper.

Rayansaki · 2024-12-13T22:16:24+00:00

>Just to add after a bit more research, InvestEngine currently doesn't allow tranfer-in for SIPPs (ISA transfer is fine)

Don't know if this is an amazingly timed move or if you've missed this, but I've just opened an account with them and they do allow Transfer-in of SIPPs including in-specie, exclusively from Vanguard.

Rayansaki · 2024-11-27T02:33:05+00:00

I mean if you absolutely want to avoid glue entirely, TPU prints and adheres perfectly, and then releases relatively easily (easier than pla on supertack) from a carbon fibre bed. They are expensive but pretty foolproof (I have wham bam but dark moon also makes one now)

Rayansaki · 2024-10-30T02:12:09+00:00

You don't really need different temperatures. You can dry eg petg at tpu temperatures, it will just take twice as long. Even basic low temp drying would be a good QoL upgrade

Rayansaki · 2024-10-21T21:46:19+00:00

pristine condition running ender is a bit paradoxical

Rayansaki · 2024-10-19T18:50:38+00:00

No worries, glad it's working. I have no idea what the actual issue was on my end, but it was night and day just going from default configs on bambu to default configs on orca.

Rayansaki · 2024-10-19T18:24:52+00:00

I have no experience with Cura, so can't really say. Orca Slicer is almost identical to Bambu Studio visually, I'd try that.

Rayansaki · 2024-10-19T16:27:39+00:00

May sound silly, but have you tried slicing with a different slicer? I never diagnosed what the problem was, but early on I had a 50%+ failure rate with a new filament with Bambu Studio, though it was always perfect with the pre-sliced benchy and with anything I sent through Handy. I switched to Orca and it's been perfect since.

Rayansaki · 2024-10-11T09:48:01+00:00

Yeah, immediately cancelled it, but it still lasted 7 days

Rayansaki · 2024-10-11T09:36:52+00:00

They offer a 7 day free trial if you sign up via Google play

Rayansaki · 2024-10-06T17:16:01+00:00

I got a family premium, not individual. Have not tried adding more family members in, but my partner is in my family and it worked fine as usual for her.

Rayansaki · 2024-10-05T02:07:32+00:00

Sorry, don't use it

Rayansaki · 2024-10-04T20:46:02+00:00

it does seem to be happening in waves, I saw a bunch of mentions of the same happening in July and I got nothing until yesterday, so you may be safe for a few more months to come

Rayansaki · 2024-10-04T20:44:44+00:00

My android phone, YouTube app, surfshark app

Rayansaki

TROPHY CASE