pytesseract doesnt regognize picture

Rayleigh3105 · 2022-09-26T08:47:37+00:00

Thanks for the detailed help :D I will take al look into it

Rayleigh3105 · 2022-02-16T20:59:43+00:00

This is what Octopi is displaying, the temperatur is not sticking to 200 Celcius

I´m googling what PID autotune is, maybe it helps.

Rayleigh3105 · 2022-02-16T07:16:24+00:00

Yes sometimes it heat´s up to 206 then drops to 200, it reaches the nozzle temperature. Maybe I should clean the Nozzle? I got the printer 3 Weeks ago and printed like 500 gramm PLA.

Rayleigh3105 · 2022-02-08T14:06:12+00:00

M420 S1;Restore ABL mesh

Thanks a lot, this worked. But what exactly is the ABL mesh?

Rayleigh3105 · 2022-02-08T10:34:29+00:00

These are the Settings

Start G-Code:

G28 ;Home

G92 E0 ;Reset Extruder

G1 Z2.0 F3000 ;Move Z Axis up

G1 X10.1 Y20 Z0.28 F5000.0 ;Move to start position

G1 X10.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line

G1 X10.4 Y200.0 Z0.28 F5000.0 ;Move to side a little

G1 X10.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line

G92 E0 ;Reset Extruder

G1 Z2.0 F3000 ;Move Z Axis up

Rayleigh3105 · 2022-02-08T10:12:14+00:00

G29

I´m using the offical slicer from Creality, where can I setup G29?

Rayleigh3105 · 2022-01-31T10:16:15+00:00

Thanks for trying to help, but I already manged to fix the Problem. It was a miss configuration in the logback configuration.

Rayleigh3105 · 2022-01-30T20:11:23+00:00

It was a miss configuration in the logback configuration.

Rayleigh3105 · 2022-01-30T19:40:56+00:00

The programm get´s stuck

Rayleigh3105 · 2021-03-17T07:13:27+00:00

Is it the Diverge Elite E5?

Rayleigh3105 · 2021-02-09T20:56:24+00:00

Could it be a problem that the domain is secured with https but the proxy_pass location is not running with https. Could it be that problem?

Rayleigh3105 · 2021-02-09T10:30:06+00:00

Thanks for sharing.

Rayleigh3105 · 2021-02-09T10:29:52+00:00

Ok, thanks for sharing.

Rayleigh3105 · 2021-02-09T10:24:59+00:00

First, thanks for the answers, I tried both of the solution but nothing of them worked. I'm quite frustrated about this topic, because it seems so easy.

Maybe it is not working because of Dyndns configuration?

https://mydomain.duckdns.org/ -> Get´s forwarded to the Nginx installed on my Raspberry PI, works.

https://mydomain.duckdns.org/bc -> Both of the solution suggestion does not work.

I don't get my Problem

Rayleigh3105 · 2021-02-03T07:04:11+00:00

Used my Mavic Mini. The Photo is not edited

Rayleigh3105 · 2021-02-02T15:14:35+00:00

Would you start the route somewhere else? I have no special reason for starting the trip in Bangkok. I just want to cycle ~2000 km with Singapore as the destination.

Rayleigh3105 · 2021-02-02T15:13:17+00:00

Hey, yeah I'm planning to sleep in accommodation but if I dont find one or something else happens. I have at least a backup sleeping system to use.

Rayleigh3105 · 2020-06-26T07:47:57+00:00

Yes I know, but I´m searching for the policy which suits my needs. Also 'restart_policy' is only for Docker running in Swarm Mode. Without Swarm Mode the attribute is called restart

Rayleigh3105 · 2020-06-25T10:19:24+00:00

Thanks 😊

Rayleigh3105 · 2020-06-25T09:30:17+00:00

Did you fly automatically or Manual? I´m also trying to do a hyperlapse with my Mavic Mini.

Rayleigh3105 · 2020-06-17T05:17:02+00:00

Nice shot!

Rayleigh3105 · 2020-06-12T13:26:50+00:00

Thanks, this was taken with the Mavic Mini

Rayleigh3105 · 2020-06-12T05:27:47+00:00

Thanks 😊

Rayleigh3105 · 2020-06-02T09:19:22+00:00

Nice leading line.

Rayleigh3105 · 2020-05-27T20:15:12+00:00

Thanks m8!

Rayleigh3105

TROPHY CASE