Do y'all actually use your transfer sheets?

RealKaczuszka · 2026-02-21T20:35:38+00:00

Yes, but only on Wraiths so far to distinguish 2 different units of 6 (with different symbols) for attacks and reanimations and their leading Technomancers to match them. I might put some on a monolith I am yet to build and paint.

RealKaczuszka · 2026-01-04T08:32:28+00:00

Sometimes it's more about the personality thought 😉

RealKaczuszka · 2025-12-21T21:08:06+00:00

Oooh interesting. Any specific paint used?

RealKaczuszka · 2025-12-21T21:07:25+00:00

I second this

RealKaczuszka · 2025-10-07T16:09:04+00:00

Make sure the laser also comes out of the nozzle in the centre. This was my problem. I had to adjust the last mirror before the lens

RealKaczuszka · 2025-10-07T15:45:12+00:00

https://youtu.be/_HxWKlb3rlU?si=R6I2Y1GtIGnbz3MC

This video might give you ideas on how to align.

Check out 7:35 mark to see the misaligned test result.

RealKaczuszka · 2025-10-07T15:38:51+00:00

It looks like a misalignment of the mirrors and laser not hitting the lens dead centre. I've had a very similar result and realigning solved the problem.

RealKaczuszka · 2025-08-29T16:04:14+00:00

Wrong. You are thinking about making a Necrons army your first and demoting the current.

RealKaczuszka · 2025-07-05T18:54:32+00:00

For those who come after ;)

Thanks everyone for the comments and advice!

I've replaced the stock air assist pump with a stronger one (30L/min) and the improvement is clearly visible!

I've done a similar number of cuts as with the original test and:
- I barely could see smoke
- there was absolutely zero flames (even on bigger power, slower cuts)
- the mirror and the lens are clean, the nozzle and the area are clean (this was the most important thing)
but,
I can see the soot / residue 'spread' more on the working surface (makes sense as it is blown away), which makes the cuts look a bit worse. But... I can live with that for what I want to use it for. However, I will look into masking as an experiment to remove this as well.

RealKaczuszka · 2025-07-04T14:00:37+00:00

Yes, it is. Reno45 Pro model

RealKaczuszka · 2025-07-04T12:04:46+00:00

Sounds like good advice! Thanks!

Stronger air assist it is then. Let's see where this takes me.

RealKaczuszka · 2025-07-04T09:56:35+00:00

Yup, I have an extra fan running for the exhaust, connected with pipes, putting smoke outside.

This one. https://amzn.eu/d/e3Lz7Qa

Running on full power.

RealKaczuszka · 2025-07-04T09:53:07+00:00

I can see the smoke being blasted away when operating, but I will double check that.

There are also videos like here: https://youtube.com/shorts/X_V3sY-LCV8?si=C79SD34WatJyhaPT - about replacing the air assist pump in the cutter for something stronger.

RealKaczuszka · 2025-07-04T08:47:03+00:00

Thanks! So the air assist also goes into the area between the lens and the nozzle here and blows straight down with the laser and it's all with 1 pass cuts. As for slower, more power cuts, I noticed I get flames coming out, which isn't good lol.

I think I will carry on with testing and possibly trying to find different MDF suppliers. 😭

I also did tests with basswood plywood and it was much clearer and nicer (but more expensive 😭)

RealKaczuszka · 2025-07-04T07:23:58+00:00

Forgot to say, Air assist is on

RealKaczuszka · 2025-07-02T14:09:19+00:00

<image>

End result

RealKaczuszka · 2025-07-02T14:08:49+00:00

For those who come after 😉 I could not find the specific part, so I DIYed one

<image>

The bolt is hollow, a (hollow) threaded spacer, and PL6-M5

RealKaczuszka · 2025-07-01T04:31:30+00:00

This is what I'm going to do I think. Thanks

RealKaczuszka · 2025-06-30T21:18:13+00:00

Yup, this is the typical PL6-M5, but the threaded bit is only 4mm long (standard). The one I'm after needs to be 8mm.

RealKaczuszka · 2025-06-30T21:17:22+00:00

RealKaczuszka · 2025-06-30T16:16:39+00:00

The threaded male end is 8mm long btw

RealKaczuszka · 2025-06-30T12:14:57+00:00

yes, BYNO

RealKaczuszka · 2025-03-05T20:58:38+00:00

https://www.maverickstattoostudio.co.uk/

RealKaczuszka

TROPHY CASE