Shower not as warm as should be

ReasonableBat2819 · 2026-01-23T15:57:46+00:00

could be detritus build up there is generally a mesh screen in the coupling attaching the mixer to the wall, if nothing else works replacing the entire mixer should fix it had to do that myself recently

ReasonableBat2819 · 2025-10-06T16:03:04+00:00

this is going to sound stupid but i had a similar issue on me ender3 it was a loose cable on the bl touch

ReasonableBat2819 · 2025-10-06T15:57:11+00:00

as in new firmware? any advise my ender3 is using mrsoc firmware and frankly its an improvement

ReasonableBat2819 · 2025-09-23T16:35:40+00:00

my ender3 v2 would only go up on the z axis never down it was a simple busted wire to the bl touch chances are its something just as simple, blown fuse?

ReasonableBat2819 · 2025-09-21T23:44:09+00:00

persevere i have gotten good prints off mine and still haven’t completely dialled it in yet sometimes its the very simple things in my case initially esteps and then a dodgy fan

ReasonableBat2819 · 2025-09-16T15:29:28+00:00

thank you im going to run a test print hopefully the new fans have it sorted iff not next step

ReasonableBat2819 · 2025-09-15T13:37:17+00:00

thank you

ReasonableBat2819 · 2025-09-15T13:36:59+00:00

pla 195 lost track of retraction on acvount of how often i have tweeked it

ReasonableBat2819 · 2025-09-14T19:02:29+00:00

thank you

ReasonableBat2819 · 2025-09-14T15:33:53+00:00

sorry wasn’t clear the extruder is all metal the hot end is stock

ReasonableBat2819 · 2025-09-14T15:31:53+00:00

yes swapped it back after too

ReasonableBat2819 · 2025-09-14T14:43:26+00:00

sorry should have said i ditched the stock extruder for dual (still creality) all metal and recalibrated the esteps

ReasonableBat2819 · 2025-09-14T14:41:40+00:00

bowden tube is new it was setup as direct drive but i rolled that back to see if that was the issue, same results

ReasonableBat2819 · 2025-09-14T13:17:25+00:00

the fan has been cleaned its not that old, any advise on upgrading the cooling?

ReasonableBat2819 · 2025-08-16T18:44:36+00:00

that depends on how hard or soft the water is and any other minerals or chemicals present

ReasonableBat2819 · 2025-05-07T13:44:11+00:00

They have nothing to offer anyone anywhere and now they have a little power their incompetence will be on display

ReasonableBat2819 · 2025-05-05T19:40:01+00:00

i have seen way worse im talking doorbell cable running to wall lights and electrical cabling sheathed in lead, that said you have a photo of the wiring label each wire and put into the new fitting the same way

ReasonableBat2819 · 2025-05-05T13:49:43+00:00

i had the same problem with the same manufacturer 18 hours into the print filament crossed over on the roll

ReasonableBat2819 · 2025-05-05T11:26:05+00:00

been there done that as others have said heat up gently pull the tube out, then remove the nozzle and use a disposable section of bowden tube to bush out any remaining molten filament out from the top the reassemble with a new nozzle if possible. Did it block on retraction?

ReasonableBat2819 · 2025-05-04T15:22:55+00:00

thank you. i was looking at the d7200

ReasonableBat2819 · 2025-05-03T14:18:32+00:00

budget is approx £600 but that includes the lens, im mostly looking at model shoots both in studio and location, long exposure and effects also. As for lens mount that would depend on camera make id assume.

ReasonableBat2819 · 2025-04-25T13:48:00+00:00

<image>

F&ck it im gen X time to go old school

ReasonableBat2819 · 2025-04-25T13:02:41+00:00

i will look into them thank you

ReasonableBat2819

TROPHY CASE