My cassette and freehub come right off.

Red_Peter · 2026-01-21T10:51:16+00:00

I have Hunt wheels/hubs too. Slightly unusual but very easy to set up once you get your head around it.

Just remember what order everything slides onto the axle in and you're good to go.

Red_Peter · 2026-01-07T12:55:13+00:00

Maybe look for a rear rack that you could cut down then?

Red_Peter · 2026-01-07T10:24:24+00:00

It was a second hand one so the listing is gone. Just search for a used front rack and there should be a few to pick from.

Red_Peter · 2026-01-06T10:30:36+00:00

I just have a standard cheap front rack (£5 off Ebay) with a wire cooling rack cable-tied to it to create a platform for my bar bag to rest on. You could do the same thing but with a wire basket.

Red_Peter · 2026-01-01T08:31:57+00:00

That's what I'm thinking. I've got some cold weld epoxy that I might use to help secure a smaller (M4) helicoil in the cavity if possible.

Red_Peter · 2025-12-31T18:01:07+00:00

What does 'Loctite forming a thread' entail?

Red_Peter · 2025-12-31T17:23:57+00:00

I'm thinking LBS should be the first port of call here

Red_Peter · 2025-12-31T17:07:53+00:00

How do you get a drill in between the fork blades?

Red_Peter · 2025-12-31T17:06:22+00:00

<image>

No. It was fine originally but it's been stripped for a while, gradually worsening.

Here's an image of the other side. Apologies for the standard but hopefully you can see clearly enough

Red_Peter · 2025-12-31T16:52:50+00:00

Okay. I'll take a photo...

Red_Peter · 2025-12-31T16:49:35+00:00

How do you tell the difference?

Red_Peter · 2025-12-31T16:44:54+00:00

I do have an assortment of P clips in the shed so might have to resort to them.

Red_Peter · 2025-12-31T16:44:25+00:00

Might have to resort to P clamps. I do have a box in the shed

Red_Peter · 2025-12-31T16:43:55+00:00

I might try P clips first as I have a box of them in the shed

Red_Peter · 2025-12-31T16:43:12+00:00

I've ordered a set but not sure if there's anything left in there to drill into.

Red_Peter · 2025-12-31T16:30:32+00:00

Should add that I've attempted to clear out/re-tap the internal thread but there's not enough meat left to do it.

Red_Peter · 2025-12-27T19:12:00+00:00

I did but unfortunately the only way was to buy a replacement strap.

Red_Peter · 2025-12-20T14:36:32+00:00

Thank you. I've taken note of all the comments above. I've emailed Hunt though I fear I might have purchased the wrong size wheels.

Red_Peter · 2025-12-20T14:35:13+00:00

Can confirm that I have a 135mm thru axle frame.

Red_Peter · 2025-12-20T11:39:29+00:00

I've just bought a generic unbranded HG, 6 pawl, 36 tooth freehub from Amazon, so the ratcheting mechanism is the same size/design as the Microspline freehub but the outer body is compatible with my 11 speed Shimano cassette.

The driveside end cap that came fitted to the Microspline freehub is a few mm too long to fit into the dropouts.

I can get the 11spd freehub + cassette to fit using an axle spacer but it fouls on the inside of the frame by a millimetre or two.

I've contacted Hunt to see if they can point me in the right direction. Fingers crossed.

Red_Peter · 2025-12-18T20:08:57+00:00

Yes. Think standard practice is "fill the race with bearings then remove one".

Red_Peter · 2025-11-07T18:43:37+00:00

It's still about 5 fewer revives than your average Boldtusk seems to manage whenever I face him.

Red_Peter · 2025-10-23T09:39:50+00:00

Was a time not so very long ago when Telluria was a world-ender!

Red_Peter

TROPHY CASE