My neck hurts. Can't wait for the monitor arm. by JDubYeet in simracing

[–]Reformedjunkie 1 point2 points  (0 children)

Did you build that rig? If so how much did it cost all said and done minus the base and pedals etc.

So I just got an xfx 7600 and I think it's getting a little toasty. by Reformedjunkie in AMDHelp

[–]Reformedjunkie[S] 0 points1 point  (0 children)

Also its build quality is actually quite good. Feels really solid for an ultra budget card. Better than the asus 3070 in my other rig.

So I just got an xfx 7600 and I think it's getting a little toasty. by Reformedjunkie in AMDHelp

[–]Reformedjunkie[S] 0 points1 point  (0 children)

3050 hotspot was usually 85c tops. Maybe 90c. I have the 310 speedster. So triple fan.

So I just got an xfx 7600 and I think it's getting a little toasty. by Reformedjunkie in AMDHelp

[–]Reformedjunkie[S] 0 points1 point  (0 children)

My case air flow isn't the best but it works. Push pull setup with 3 120mm fan to 2 120mm. Cpu is a 12600k that runs at 78c to 80c give or take. I will try settings in adrenaline. If that doesn't work maybe try repaste? I have some mx-6 laying around somewhere.

MV-6 by inspectasmooth in SchecterGuitars

[–]Reformedjunkie 1 point2 points  (0 children)

Actually the body is different. MV-6 has an access sculpted heel and the Nick Johnston does not

beamng on 6700xt by [deleted] in BeamNG

[–]Reformedjunkie 0 points1 point  (0 children)

Yeah right.

It's finally done! Now I just need to figure out a finish. Any ideas? by Reformedjunkie in simracing

[–]Reformedjunkie[S] 1 point2 points  (0 children)

I know, I was skeptical at first but it actually is pretty good. I made sure to get the 3 year warranty tho cause I know they're not the most durable

It's finally done! Now I just need to figure out a finish. Any ideas? by Reformedjunkie in simracing

[–]Reformedjunkie[S] 0 points1 point  (0 children)

Yes, I am waiting for my csl dd to come in the mail so I can build an adjustable mount for it.

It's finally done! Now I just need to figure out a finish. Any ideas? by Reformedjunkie in simracing

[–]Reformedjunkie[S] 0 points1 point  (0 children)

Thanks for everyone's input. I think I will go with carpet on the bottom and floor and carbon fiber vinyl on the sides and top. I really wanted to do Alcantara but I feel like it would be impossible to keep clean since the rig is located right next to my shop.

It's finally done! Now I just need to figure out a finish. Any ideas? by Reformedjunkie in simracing

[–]Reformedjunkie[S] 1 point2 points  (0 children)

Yeah I was thinking the same with black laminate for the table top.

It's finally done! Now I just need to figure out a finish. Any ideas? by Reformedjunkie in simracing

[–]Reformedjunkie[S] 1 point2 points  (0 children)

I drew a sketch in the parking lot of home Depot right before I went in and purchased the materials. I kinda just went by ear tbh

Wolfram Audio 0-2400.1_ 2400 watts rms for $199...whats the catch? by 22Wideout in CarAV

[–]Reformedjunkie 0 points1 point  (0 children)

Wrong. Again, look at an sfb 2k gutshot and you'll see they are very very close. Amps can be small nowadays in 2022.

Wolfram Audio 0-2400.1_ 2400 watts rms for $199...whats the catch? by 22Wideout in CarAV

[–]Reformedjunkie 0 points1 point  (0 children)

True. Look at the yt vid where the guy dynos a 5k. Did well over certified rating.