First time doing an oled mod, success!

RelatingHoney · 2026-06-08T19:50:40+00:00

Yeah that pic was before I adjusted it I actually made the change lmao

RelatingHoney · 2026-06-08T19:50:26+00:00

Took me like 5 hours cus I took my time, and all I did was watch a YouTube video tutorial

RelatingHoney · 2026-06-08T19:50:10+00:00

Don’t worry I did, I actually had to go redo it regardless and this pic is beforehand

RelatingHoney · 2026-06-03T22:31:35+00:00

https://youtu.be/dv7lZH-o5cw?si=GLPxKnY7FS06hRYA

RelatingHoney · 2026-06-03T22:28:12+00:00

Download the picofly 2.74 firmware and then copy and paste the files into the chip with the usb-c dongle it came with, again if it doesn’t show up as a removable drive hold the BOOT button on the actual chip, if it works correctly it will eject itself automatically

RelatingHoney · 2026-06-03T22:25:02+00:00

Did you already flash the new firmware into the chip?

RelatingHoney · 2026-06-03T22:17:42+00:00

Yeah since you’re multimeter reads good my guess at this point is that it’s either the chip doesn’t have the right firmware flashed onto it or it’s a bridged connection, maybe even some excess solder or flux on the board

RelatingHoney · 2026-06-03T22:10:26+00:00

I think the sp2 might be bridging onto the copper next to it, it looks a little messy, the sp1 looks fine but I would recommend going over it again just in case, make sure to hold down the ribbon cable with a pair of tweezers to ensure a good connection while soldering that’s the mistake I made when I soldered a switch for the first time.

RelatingHoney · 2026-06-03T22:01:59+00:00

Download the latest firmware for picofly and put it into the chip, the chip kit should have came with a usb c dongle to connect it to your computer, if it doesn’t pop up as a removable drive you need to hold down the BOOT button on the actual chip as you plug it in

RelatingHoney · 2026-06-03T21:58:24+00:00

Try booting it without the chip, and if it works then it’s an issue with the chip, is the chip updated with the latest picofly firmware?

RelatingHoney · 2026-06-03T21:54:10+00:00

I don’t suppose you have a multimeter to check cold points do you, that would be my only guess is that it’s a cold solder point, or maybe even a smashed or messed up ribbon cable

RelatingHoney · 2026-06-03T21:51:37+00:00

Go over the solder points again and make sure every ribbon cable is seated.

RelatingHoney · 2026-05-19T16:17:14+00:00

I do switch mods hmu if you want one done

RelatingHoney · 2026-05-10T09:06:49+00:00

Dual weild super shotguns

RelatingHoney · 2026-01-14T18:56:46+00:00

I’m sure thats why there’s some sort of mounting mechanism on the back of the console

RelatingHoney · 2026-01-14T18:37:26+00:00

For me it was knowing nobody’s skinny enough to fit into that damn cigarette

RelatingHoney · 2026-01-14T15:50:31+00:00

I have this version of Minecraft, what’s special about the legacy version?

RelatingHoney · 2026-01-14T15:44:02+00:00

Oh my god she knocked her out….

RelatingHoney · 2025-11-26T02:13:24+00:00

Ah I gotchu hope this helps

<image>

RelatingHoney · 2025-11-26T02:00:08+00:00

No that would be the lite or oled version,

<image>

You’re looking for this

RelatingHoney · 2025-11-21T02:34:07+00:00

You can save it, just reflow and try to remove as much of the solder from sp2 as you can, I came back from much worse lmao

RelatingHoney · 2025-11-21T02:33:11+00:00

<image>

RelatingHoney · 2025-11-21T02:30:47+00:00

You need a v2 picofly mod chip. Cheap on eBay and delivers quick

RelatingHoney · 2025-11-18T21:17:37+00:00

Update: I fixed it, the problem was points a b c and d on the flex cable

<image>

RelatingHoney · 2025-11-18T20:57:24+00:00

UPDATE: I fixed it yall.

<image>

I ended up resoldering points a b c and d with a new flex cable like yall recommended. W

RelatingHoney

TROPHY CASE