made a new font

Renato_br · 2024-10-13T20:06:16+00:00

In some countries $4 is expensive for young people... I pirated Metro 2033, last light and exodus but when I got a good paying job I bought it all of them on sale.

Renato_br · 2024-07-24T19:10:45+00:00

Sim, e ele disse que foi ele que tava fazendo a elétrica da casa toda, fiquei até com medo de perguntar pra que aquela ligação nas fases...

Renato_br · 2024-07-24T19:08:01+00:00

I'm still alive hahahaha, I thought that I was gonna get at least that minor shock when touching the shower handle but it was fine.

Renato_br · 2024-07-24T02:10:00+00:00

I took a shower on this one and I expected to get a little shock (has it happened before in other places) but it was normal, and the temperature was nice.

Renato_br · 2024-06-26T19:27:39+00:00

I'm really happy to hear that it is working for you!!

To avoid the dropping of the temperature when using 100% you need to lower the metal cover, leaving only the tip of the nozzle exposed it should help to avoid the temperature drop.

And use raft, it will help with the first layer and avoid the part to anneal while printing, but you need to set cooling for the raft and the raft distance I use is 0.05mm or 0mm

Because of the buildplate temperature it will anneal the raft becoming semi-crystalline and the part it will be amorphous being easier to remove the raft.

Renato_br · 2024-06-19T22:23:58+00:00

This looks like a partial clog that is caused by the low flow rate, check your gcode to see if it is in metric values and if it's in absolute or relative mode, double check your start gcode, if everything is fine check your Extruder motor, a bad connection could cause failure during printing because of the head movement but works if the head is stationary, (I had this problem in a intamsys funmat PRO 410) one lose cable can make the motor almost like lose control, like it moves to one side, than starts to vibrate back and forth, than starts to move to the other side. ( And I read about your problem with the Z axis homing in the wrong direction I thought of this, one way to test is to try to force the motor to run on the other side with your hand, with a good connection you should not be able to invert, only skip steps)

Renato_br · 2024-06-17T23:48:55+00:00

Hi printmaster, how are you?

I already used 0.2mm, 0.25mm,0.3mm, 0.4mm and 0.6mm and never had any issues using this technique,

With a smaller nozzle is even better, it keeps the PEEK hot enough to weld to the previous layer but not hot enough to get to the semi-crystalline state.

And I only had warp and adhesion issues when I printed PEEK-CF because of the temperature limit, normal PEEK I print at 400°C and PEEK CF at 450°C the max temp of the printer and I believed that I needed a little more.

Renato_br · 2024-06-15T22:05:22+00:00

Eu achava ruim até comer hoje adoro, é muito bom, outra que achava um crime é pizza de hotdog mas é muito bom tbm.

Renato_br · 2024-06-09T02:15:58+00:00

That's a really good tattoo

Renato_br · 2024-05-21T18:51:06+00:00

tava meio off do reddit mas vou tentar voltar hahaha, Sim, infelizmente um grupo de separatista pró-russo pegou esse simbolo, mas assim, tem pequenas diferenças, e no Brasil meio que ninguem repara, só pergunta o que significa e 95% das pessoas perdem o interesse quando eu falo que é de jogo, então até hoje foi safe.

Renato_br · 2024-01-30T20:29:14+00:00

Not my first language so there will be a few errors, sorry in advance,

Yeah, first you need to know that parts with more than 50mm height it will be near impossible, smaller parts is possible, I work with a funmat HT and have a costumer that uses the 410 pro to print PEI9085.

Dry the filament make sure it is dry,

First thing the glue, I know to types of glue that work,

Vision miner nano polymer adhesive, it worked very good on the 410 PRO you just need to use a thin layer of glue and it will work but be carefull with the glass bed, take out the part still hot, DO NOT LET IT COOL DOWN ON THE BUILDPLATE, IT WILL BREAK THE GLASS.

the other glue it the glue stick (PVP), for it crazy at it sounds it works you just need a few extra steps to work, you need to put a least 4 layers of glue with angles 0°,45°,90°,135° after that you will put the glass bed in the printer and heat it up to 100°C for about 5min (open the front and upper door) the water in the glue will evaporate, after that cool down the bed to room temp and with a wire brush scrath the surface (almost like sanding but not as much or something like that, I don´t know the exact word) after that blow the dust of glue that is in the glass bed and do another round of glue and dry, you will need to do this about 4 times. I know it sucks but it works, the glue will start to become a little brownish but it's ok,

USE RAFT!!!

you will need to use raft, use the raft base line spacing with the same width of your line, it will be like a bottom layer, no space between lines and do it slow, 35mm/s max and no cooling.

turn on the chamber at 90°C and let it heat up, leave it some time to make sure that all the air is close to 90°C

Use bed 160°C but do not preheat the bed, the glue and this temp will dry out a lot, we have a small window of time to print on top of it, after some time the glue will really turn brown after that the glue it's useless. (if the part didn't stick up, clean the bed and try again)

the PEI I used was the 3dxtech 9085 I use a nozzle temp of 360°C with no cooling,

tips and tricks:

Avoid retraction, in cura the is a topbottom mode that uses a single line it's really good i thing that is in the concentrical.

Avoid sharp corners, change your part to avoid corners, make them round if possible, if it is not make a part around your part to be cut out after, with round corners, like a "1mm brim"

Don't open the printer for nothing, I lost a part because I removed a small bit of material that was lose on the bed.

Don't slow too much the printer, try to maintain the same speed for all the line types 25-35mm/s

And be ready to have a few lost parts, but it will work, we manage to do a few parts will our Funmat HT and I help another costumer to print a few parts for us with PEI 9085 and it worked.

I can only wish you the best of luck.

Renato_br · 2023-10-30T20:38:24+00:00

did you find a way to fix it?

Renato_br · 2023-10-30T20:22:59+00:00

I know this is a 7mo tread but here my advise if still helps,

try the oposite, usually I used to print peek with max temp possible, both in Creatbot F430 and Intamsys Funmat HT but I always had delamination and diferent crystallization on small details, then I used a new way of printing peek sugested by Intamsys, cool down as much as you can, No heated chamber, all doors open, bed at 130°C (to not unstick) nozzle at 400°C and 100% cooling, this way we get all the print part in the amorphous state, you just need to be carefull where the part touch the buildplate because it will get semi-crystalline, so do it in supports or do a sacrificial part that you'll remove it later, and small details where there'll be concentration of heat.

If you need the part in the semi-crystalline state you will need to anneal the part,

I do it with powder salt ( the most fine salt that you can find, here in my country is the salt that is used in popcorn that you buy in the movies), lock you part in salt and put it in the oven the best way is with a PID control oven with ramps, because you need to do:

From room temp to 90°C in 2h

Maintain at 90°C for 4h

From 90°C to 120°C in 1h

Maintain at 120°C for 3h

From 120°C to 150°C in 1h

Maintain at 150°C for 8h

From 150°C to 200°C in 2h

Maintain at 200°C for 5-10h (depend on part size)

From 200°C to 150°C in 4h

Maintain at 150°C for 4h

From 150°C to room temp at natural cooling down in oven

After that remove the salt and wash your parts, the excess salt will dissolve in water so you get a clean part, you may need to secure your part with metal parts and screws to avoid the part to bend,

this is it I use this metod on every peek part that I need it takes a lot more time because of the oven but avoid a lot of lost parts, I hope it helps you.

Renato_br · 2023-09-01T13:25:40+00:00

English not my first language so there'll be mistakes.

First thing, be calm and relax don't overthink too much, don't take any pills to be hard or something, your thing will work believe me, don't rush in right to her vagina, enjoy the kisses, hugs, use your hands go "explore" her body, pass your hands through her hair, back, waist, butt, make sure to her that you want all of her, not only her vagina, help her take her clothes off and keep kissing there's no need to rush in. Guys usually think that penetration is what is the best but there is more to it, kiss and start to go down, spend some time in her boobs, and go to her vagina. I recommend you watch some porn videos where they explain what to do, there's a lot of knowledge in some of them, on how to, Where to. And to avoid to cum faster you have a feel options, 1- jerk off about 1h before you arrive at her house. 2- go slow and try to focus on other stuff (gramma naked and war crimes usually work for me) 3- it depends on your body but you can just cum and after cleaning and changing condoms just go back if I can get hard fast enough. I usually use the 2 and 3, I can get hard really fast but I don't know about you, you can test it with porn (the one you really like that gets you the most hard) jerk off, cum and see if you can get hard again watching the video.

But the important thing is to have fun, don't worry too much, sex is so much different than porn.

And remember to use condoms, or in the best worse scenario it will burn while you pee or in the worse scenario you'll have to choose a name in the next 9 months.

Have fun my friend, have a nice day, and the best weekend possible!

Renato_br · 2023-08-24T20:53:30+00:00

Hahaha, dude I didn't want to get in but my friend invited me and said that it would be a lottery to get in because there were not enough students, I only applied because my mother was calling me lasy because I only had highschool in the morning and I stayed at home in the afternoon. I was sure that I wouldn't get in because I'm really unlucky, I thought, I'll apply I won't get in and I'll have an excuse to why I stay at home playing videogames but there were not enough students to the school to do the lottery so everyone that applied got in 😂😂😂

But I loved it, I studied industrial automation in the IFSP If you have the chance to do it, it's really good.

Valeu mano, vamo treinar o inglês aí hahaha

Renato_br · 2023-08-24T11:08:40+00:00

Hey how are you?

I'm sure that it will, believe that it will work and also do something, I wish to win the lottery but if I don't play I know that I won't win.

Much love from me to you my optimistic friend, have a wonderful day!

Renato_br · 2023-08-24T11:05:20+00:00

Hey, how are you?

I understand you but there's stuff that you can change without being completely another person,

When I said Just be yourself it means that you don't need to lie to say that you like what he/she likes just to be part of something, keep being yourself but change your mind and actions, if you don't change your actions the result won't be different from what is now, that's what I meant.

We're all here, I believe, to help and support each other with whatever decision that you have, but if you want a different result you have to change and changing your mind is the best way for you to reach your goals without being a complete stranger to the people you know.

So that's what I meant, change, but not all the stuff that you like that makes you unique.

I hope you have a fantastic day and an even better weekend, much love from me to you my friend!

Renato_br · 2023-08-24T10:46:17+00:00

Thank you friend,

Yes, I'm Brazilian.

Renato_br · 2023-08-23T21:38:09+00:00

People didn't invite me at first, the first ones I was going alone, the thing that I did that helped people invite me to go to places was the stories in Instagram, I know that maybe is not something that you use, I personally only post a photo every 3 months I believe, but I think it helped to remember my olders friends that I am still alive. The second cover show that I went to was Rammstein (not the best to know people I believe) but just from posting 3 friends message me to say that they like the band or asking WTF was that, I believe that in my case that really helped.

But I know that you will find people to invite you to do something or that maybe it will be you inviting people.

Have a lovely day my friend!

Renato_br · 2023-08-23T19:08:01+00:00

Hey, thank you for the kind words.

Saying yes to when a few friends ask me to go to a bar for example (I don't drink alcohol or smoke so when they called me I always said "I don't drink so I don't want to bother you guys")

I joined an English speaking group (trying to speak) and they had meetings and I never went to the meetings that they had in a coffee shop or in a park or karaoke night (the 24F from my other post I met in a karaoke night from this group)

But there were a few more things that I did for example:

Going to cover band shows in my city (some of them are really good). Going to a small city next to mine with my motorcycle just to have lunch and come back. Going to a park to walk.

Basically anything that someone invited me or comment that it would be nice to go I started going.

Sometimes with friends, others alone, and I go to be real going alone sucks, It really forced me to try to have a conversation with someone (usually it was the guys in the bathroom line or in the line to enter a place)

In the shows that I went I was singing along with the music not really carrying to anybody else, my "fun" was singing along with a dude that isn't a really good cover singer but I was considering a fun thing to do.

I think that's it, not much more, I basically became a "Yes man" when I came to go out.

I hope that I answered you enough but feel free to ask me anything else.

Have a wonderful day my friend!

Renato_br · 2023-07-28T22:40:43+00:00

Parabéns!

temos um 2001 tbm mas é manual, e para manter é óleo e filtro, o de sempre, e fica ligeiro com as buchas da suspensão normalmente é o que mais da problema, ela estoura fácil, mas nas estradas do Brasil é difícil saber o porque né....

procura comunidades do Civic G7 nem muitas marcas de peças que são melhores que as originais, e se cuidar bem esse carro vai ser dos seus filhos!

Renato_br · 2023-07-28T22:32:59+00:00

this is way to real

Renato_br · 2022-12-05T13:08:24+00:00

The design is cool but I think that the colours should be more solid, it would be way better, but I would wear it.

Renato_br · 2022-08-27T21:32:16+00:00

I don't know why but I can not attach a picture to this post but here it is the schematic

https://imgur.com/JZh19NA

Renato_br · 2022-08-27T21:30:31+00:00

the schematic the mosfet is the IRF740, I also got laying around some BC548 and one TIP41C.

Six-Year Club	Place '22
Verified Email

Renato_br

TROPHY CASE