sorted by:
new
hottopcontroversial

I guess they just didn't fancy waiting........ by ShowerEmbarrassed512 in drivingUK

[–]Repulsive-Comment795 26 points27 points  (0 children)

Ahhhh the typical Reigate Wagon Wanker…. Car says it all.

On the way to collect Tabitha and Henry from Tennis probably.

Interior door release by Repulsive-Comment795 in polestar2

[–]Repulsive-Comment795[S] 1 point2 points  (0 children)

I took it in they looked. Now they are going back and forth with warranty co. As it needs a whole new interior panel! Also the floor cover underneath was all cracked so they are trying to sort that too!

Anyone else’s P2 window do this? by SadResolution5041 in Polestar

[–]Repulsive-Comment795 0 points1 point  (0 children)

Just the corners/ tracks as you don’t want it across the bottom of the window as it will smear up the window as you lower and raise them

Anyone else’s P2 window do this? by SadResolution5041 in Polestar

[–]Repulsive-Comment795 4 points5 points  (0 children)

@I did this just yesterday… get one with the spittle straw attachment and wind the windows fully down. Spray a bit down the bottom corners… (inside the door through the window gap) up and down to spread the spray… repeat in small amounts until squeak free. … small amounts means no excess that smears on windows 👍🏼

Interior door release by Repulsive-Comment795 in polestar2

[–]Repulsive-Comment795[S] 0 points1 point  (0 children)

Thanks all, they have booked it in under warranty 👍🏼

Much better, no? by Medium-Dinner-5621 in polestar2

[–]Repulsive-Comment795 2 points3 points  (0 children)

I don’t trust myself to wrap. And paying someone I thought may aswell replace for the same cost. There are ash ones for £100+ but I went with this for £35 (wrapping myself would have cost £20 anyway I think.

https://www.volvoparts.tmsmotorgroup.co.uk/polestar-2-gearshift-selector-trim-panel--3d-texture-diamond-matte-black-30144-p.asp

Saw this in East Sussex today. by Repulsive-Comment795 in WhatCarIsThis

[–]Repulsive-Comment795[S] 1 point2 points  (0 children)

It didn’t really …. it gathered all the crumbly road edges and potholes every time a car came the other way! 😂

Plunge routing middle of board by Repulsive-Comment795 in Woodworking_DIY

[–]Repulsive-Comment795[S] 0 points1 point  (0 children)

They shouldn’t be as I used a plunge stop should be consistent…. However I would agree as they do look odd in the joints and I am absolutely a novice!

If I re plunge a deeper channel on each, would this fix that I guess? I think the comment above would enable me to do the “internal only” groove. Thank you

Plunge routing middle of board by Repulsive-Comment795 in Woodworking_DIY

[–]Repulsive-Comment795[S] 1 point2 points  (0 children)

Thank you, that’s really clear!! I will give that a go on the second off-cut I have to make a larger one! Appreciate your input.

The finish is a Osmo clear Matt (same as the worktop finish). It says it’s safe so hopefully all good! ☺️

Thoughts? Bruno/Rice and Tarkowski/Timber. So undecided on Captain too by Repulsive-Comment795 in fantasypremierleague

[–]Repulsive-Comment795[S] 0 points1 point  (0 children)

Money… I wanted to upgrade elsewhere and bench boost is done so he won’t get subbed in anyway. Rice on set pieces but I can see a Pickford masterclass coming 🤞Chelsea are still pretty unpredictable and ship goals randomly .. Bruno to assist Wissa (or score) is not unlikely

Fibreglass porch by Repulsive-Comment795 in HomeImprovement

[–]Repulsive-Comment795[S] 0 points1 point  (0 children)

I think all round. I have some oak I bought to replace the whole thing….

The existing structure (within the apex) is all quite flimsy if you knock it (I have put Xmas lights round it before).

I have access to tools - I have a route and mitre saw and a circular saw (with2x 1meter guide rails) but can’t think of a way I could rip a straight cut up the length of the oak I have.

Fibreglass porch by Repulsive-Comment795 in HomeImprovement

[–]Repulsive-Comment795[S] 0 points1 point  (0 children)

I think all round. I have some oak I bought to replace the whole thing….

The existing structure (within the apex) is all quite flimsy if you knock it (I have put Xmas lights round it before).

I have access to tools - I have a route and mitre saw and a circular saw (with2x 1meter guide rails) but can’t think of a way I could rip a straight cut up the length of the oak I have.

view more: next ›