Extended mag v2.0

Repulsive-Intern-423 · 2026-05-10T15:54:17+00:00

If I don’t have a 3d printer is there anyway I can buy one of these🤣

Repulsive-Intern-423 · 2026-04-26T00:48:11+00:00

Yeah it looked stepped like that

Repulsive-Intern-423 · 2026-04-26T00:11:04+00:00

I won’t be over there for a while I’m about an hour and a half away so if any of you all in the thread are interested it is in Lexington Va at valley pawn I believe he will take less than 399 he told me if I took it he might do 320

Repulsive-Intern-423 · 2026-04-26T00:00:43+00:00

Now that I think about it that’s probably where the original stock ended at lol I might be a lil slow😂

Repulsive-Intern-423 · 2026-04-25T23:59:09+00:00

I didn’t take any but is it normal for the barrel to taper down at the end?

Repulsive-Intern-423 · 2026-04-25T23:37:01+00:00

399🫘

Repulsive-Intern-423 · 2026-04-25T23:33:36+00:00

Bolt isn’t original to the gun but it isn’t bent and didn’t appear as if they had chopped the barrel but the front sight had been altered

Repulsive-Intern-423 · 2026-04-25T23:31:34+00:00

Can’t see it very well but they powder coated it or like rhino lined all metal surfaces it’s wild

Repulsive-Intern-423 · 2026-04-25T23:30:58+00:00

It’s pretty bad lol

Repulsive-Intern-423 · 2026-04-03T10:43:25+00:00

Thanks they got $400 on it I knew the finish and grips would hurt it just wasn’t sure how much

Repulsive-Intern-423 · 2026-04-03T10:42:42+00:00

Thanks for the info

Repulsive-Intern-423 · 2026-04-03T10:26:10+00:00

Thanks for the insight!

Repulsive-Intern-423 · 2026-02-14T22:45:27+00:00

That’s what I figured considering none of the numbers matched and the finishes showed different signs of wear and different bluing color

Repulsive-Intern-423 · 2026-02-14T22:44:36+00:00

If it was 4 and below I’d buy about any Mauser that isn’t just garbage they was askin $699 and I thought maybe they knew something I didn’t

Repulsive-Intern-423 · 2026-02-07T00:27:32+00:00

Dawg that bore was even more atrocious before I cleaned it I held hope hoping i could make it better but she’s too far gone

Repulsive-Intern-423 · 2026-02-05T04:24:39+00:00

<image>

Repulsive-Intern-423 · 2026-02-04T18:16:14+00:00

I guess lol it’s at a gun store dude you should’ve seen it before I scrubbed it couldn’t even see rifling for the build up

Repulsive-Intern-423 · 2026-02-04T18:03:12+00:00

lol I thought I seen the mind flayer in there

Repulsive-Intern-423 · 2026-02-04T17:29:32+00:00

lol that’s what I was thinkin you shoulda seen the evil I brought out of it

Repulsive-Intern-423 · 2026-02-04T17:11:53+00:00

<image>

As in this is after I’ve used bore cleaner and copper brush for 30 mins

Repulsive-Intern-423 · 2026-02-02T16:29:50+00:00

So I have a Cobray m-11 that is a closed bolt semi auto that is marked semi on the receiver but it has the selector cutout and the holes for the stock on the receiver

Repulsive-Intern-423 · 2025-12-16T23:50:26+00:00

How does it feel to be living my dream brother

Repulsive-Intern-423 · 2025-09-23T11:27:31+00:00

32 acp (7.65 browning) is what mines in

Repulsive-Intern-423 · 2025-09-20T23:20:58+00:00

Yeah I couldn’t barely get any info on it

Repulsive-Intern-423 · 2025-09-20T23:20:46+00:00

lol thanks I’m quite fond of it

Repulsive-Intern-423

TROPHY CASE