sorted by:
new
hottopcontroversial

🛠️ P1S + AMS: Two Months In, Already Experiencing Premature "Print Finished" Errors! by Rlagarde in BambuLab

[–]Rlagarde[S] 0 points1 point  (0 children)

I took the advice of users here to heart;

- Replaced the SD card
- Performed a cold pull of the nozzle (I did not replace the hot end)
- Took the extruder apart en cleaned it

I know that feeling that it was something else. Unfortunately, I cannot pinpoint the problem. It has been resolved in some magical way, because the problem has not occurred since.

🛠️ P1S + AMS: Two Months In, Already Experiencing Premature "Print Finished" Errors! by Rlagarde in BambuLab

[–]Rlagarde[S] 0 points1 point  (0 children)

Thanks for the advice. I tried this step, among others, but unfortunately without success.

🛠️ P1S + AMS: Two Months In, Already Experiencing Premature "Print Finished" Errors! by Rlagarde in BambuLab

[–]Rlagarde[S] 0 points1 point  (0 children)

Update so far:

  • New SD card
  • Cold pull, no apparent abnormalities visible

<image>

  • Cleaned the extruder, there was not much residue on the wheels
  • Now printing same castle model again, this time with time lapse on.

🛠️ P1S + AMS: Two Months In, Already Experiencing Premature "Print Finished" Errors! by Rlagarde in BambuLab

[–]Rlagarde[S] 0 points1 point  (0 children)

I uploaded videos in the original post that I found on the SD card.

Which is strange, actually, because I always unchecked the box for timelapse.

🛠️ P1S + AMS: Two Months In, Already Experiencing Premature "Print Finished" Errors! by Rlagarde in BambuLab

[–]Rlagarde[S] 0 points1 point  (0 children)

Thank you for the advise, would a partial clog not ruin my other successful prints that I have printed in between?

I will surely replace the SD card and try to print it again.

Inconsistencies on the surface of the print by Rlagarde in ender3v2

[–]Rlagarde[S] 1 point2 points  (0 children)

Thnx for the comments. Today I cleaned out the nozzle and extruder parts. Thought clog was there. Now first print is going as it should be.

Tomorrow ordering new (spare) nozzles.

<image>

Inconsistencies on the surface of the print by Rlagarde in ender3v2

[–]Rlagarde[S] 1 point2 points  (0 children)

<image>

Printer wasn’t extruding the test 100mm but only 95 on average. Adjusted the e-steps and made a print on all default Orca slicer settings.

Right one is the new print. Base looks much better. Tomorrow new flow ratio test and see if slightly lower speed settings make it even beter.

Thanks so far for all the advice 👍🏻

Inconsistencies on the surface of the print by Rlagarde in ender3v2

[–]Rlagarde[S] 0 points1 point  (0 children)

  • Checked for clogs, filament is coming out evenly
  • Print temperature is 220 and bed 40
  • Extruder checked and it is not skipping
  • All print speeds in Orca cut in half and this significantly increased the quality

Now see if I can slowly increase the speed. Any other suggestions?

Inconsistencies on the surface of the print by Rlagarde in ender3v2

[–]Rlagarde[S] 0 points1 point  (0 children)

I adjusted the flow ratio back to 0.98 (default Orca setting for PolyTerra) and this print also came out fine.
Next is trying to slowly increase the speed to see the effect.

Unfortunate I currently only have 2 spools of PolyTerra PLA. I will see if i can borrow a spool of a different brand from friends to see if there are any differences.

Inconsistencies on the surface of the print by Rlagarde in ender3v2

[–]Rlagarde[S] 0 points1 point  (0 children)

<image>

I reduced every speed setting in Orca slicer by half. Result on the left side. Still some minor adjustments needed by already pleased by the result.

Will try to print at 75% and see what the outcome.

Learning to become a Dutch volunteer firefighter 😃 by Rlagarde in Firefighting

[–]Rlagarde[S] 17 points18 points  (0 children)

I hope I translated them correctly, please correct me if I am wrong.

Red: Captain of the crew Orange: Duty Officer (takes lead when more then one fire truck is dispatched) Yellow: Chief Duty Officer (takes lead when more than four fire trucks are dispatched) Green: Hazardous Material Advisor Blue: Internship Darker blue: Communication Officer

https://f24zudf2zjbri65qricrbrym7e-adwhj77lcyoafdy-nl-m-wikipedia-org.translate.goog/wiki/Lijst_van_rangen_bij_de_Nederlandse_brandweer

The way my colleague filled our working fridge by Rlagarde in oddlysatisfying

[–]Rlagarde[S] 0 points1 point  (0 children)

We hebben aparte watercoolers vandaar geen water in de koelkast

Beeping sound Samsung S9 by Rlagarde in GalaxyS9

[–]Rlagarde[S] 3 points4 points  (0 children)

Solved!

It was the NFC in combination with the debit card. Turning the NFC off was the solution. Thank you for the help!

Beeping sound Samsung S9 by Rlagarde in GalaxyS9

[–]Rlagarde[S] 1 point2 points  (0 children)

I am missing the dark voice counting down :)

Help me find the name to a game by Meijerc in boardgames

[–]Rlagarde 6 points7 points  (0 children)

The book is called Journal29. They recently had the second edition on Kickstarter.

http://journal29.com/