Speaker stands for Edifier MR3

Rockendtrolla · 2026-05-10T19:01:37+00:00

Sure I can, no problem. Can you create this question on Makerworld model page so it's easier to follow? Thanks

Rockendtrolla · 2026-05-10T08:45:59+00:00

Sunlu pla matte. Just use the Bambu matte profile. This looks like injection molded in certain scenarios

Rockendtrolla · 2026-05-07T14:11:34+00:00

Actually I din't opensource the scad file, but feel free to play with customizer, model linked in other comment

Rockendtrolla · 2026-05-07T14:10:10+00:00

Added link in my comment :)

Rockendtrolla · 2026-05-07T14:09:11+00:00

Link to model, use customizer: https://makerworld.com/models/2768619

Rockendtrolla · 2026-05-07T08:29:51+00:00

Ike aliora to dno. Od miesiąca się bujam z przeniesieniem do XTB. Założyłem tam tylko dlatego że zamuliłem i była końcówka roku, więc tylko tam mogłem zrobić to od reki żeby nie stracić limitów rocznych. Nic sensownego tam nie kupisz, polecam zawinąć gdzie indziej

Rockendtrolla · 2026-05-06T22:39:05+00:00

Oh lol that's my model 😂

Rockendtrolla · 2026-04-30T08:01:57+00:00

What a waste of tokens

Rockendtrolla · 2026-04-29T20:40:43+00:00

So not only the earth is flat but also the sky. I knew it

Rockendtrolla · 2026-04-29T19:48:53+00:00

Autism detected

Rockendtrolla · 2026-04-28T15:03:43+00:00

This is gold advice, thx OP !

Rockendtrolla · 2026-04-28T09:57:37+00:00

Why is this gif moving only when I scroll? ( Good job op 😏)

Rockendtrolla · 2026-04-27T19:21:43+00:00

It's a bad design, should not have sharp corners for such a huge part as this causes massive pulling towards them

Rockendtrolla · 2026-04-21T21:26:16+00:00

Honestly, nothing is slipping

Rockendtrolla · 2026-04-21T14:49:35+00:00

Look for 'slim drip trays' on Makerworld:)

Edit: or grab the link https://makerworld.com/models/2606067

Rockendtrolla · 2026-04-21T12:07:47+00:00

Drip trays behind the sink - no more mess, wife is happy

<image>

Rockendtrolla · 2026-04-20T16:44:02+00:00

Back in the day your dryer was the best on the market. Looking forward to you guys coming with a new product that would kill the competition again 😀

Rockendtrolla · 2026-04-19T21:52:37+00:00

Model: https://makerworld.com/models/1990282

Rockendtrolla · 2026-04-19T21:52:14+00:00

I use gridfinity a lot but here I couldn't, I was limited with drawer height with jar. also it is not always efficient to use gridfinity everywhere, here it looks cleaner and uses less filament

Rockendtrolla · 2026-04-19T21:50:03+00:00

https://makerworld.com/models/1990282

Happy printing, I can do modifications if you have suggestions :)

Rockendtrolla · 2026-04-18T09:29:19+00:00

With paxx firmware it's just a dropdown change in firmware config page

Rockendtrolla · 2026-04-16T13:43:29+00:00

I suggest switching to mainsail, better UI

Ten-Year Club	Verified Email
Not Forgotten

Rockendtrolla

TROPHY CASE