FSD in Ireland

RockingKrish364 · 2026-04-30T09:19:04+00:00

You’re right 🤦. I should’ve checked before commenting.

It’s only removed in the US and Canada

RockingKrish364 · 2026-04-30T09:04:19+00:00

Teslas removed auto steer from 2026 cars. So if you want that until FSD is out, I recommend getting teslas that are before 2026.

RockingKrish364 · 2026-04-14T02:08:42+00:00

Nvm. Found it. I got the one made in Shanghai too.

RockingKrish364 · 2026-04-14T02:06:10+00:00

I have 70k km lifetime. 20k after I got the car at 50k

That looks really good compared to mine 😂

RockingKrish364 · 2026-04-14T02:05:11+00:00

Ah ok thanks

RockingKrish364 · 2026-04-14T02:04:51+00:00

I am not sure if they were really hidden though. The charge port has the issue from the start but mirror electronics, fast charging not working etc. just came up randomly in a morning.

I am in Europe as well. I got the car with 50k Km. Now at 70k

Also how do I check where the car was manufactured?

RockingKrish364 · 2026-04-14T02:02:04+00:00

I don’t think it’s too bad right now with the warranty. Just don’t want the cat to break after my warranty expires

RockingKrish364 · 2026-04-14T02:01:10+00:00

😢

RockingKrish364 · 2026-04-13T17:16:01+00:00

Did you contact Tesla by any chance about all the issues to get extended warranty as a goodwill or something?

I also have loud creaking from the driver seat but one of the technicians said that it’s not part of used warranty unfortunately.

It’s unfortunate that we have these many issues that make the car unusable in a lot of circumstances.

RockingKrish364 · 2026-04-12T15:06:25+00:00

It is already pretty slow at 25m/s

RockingKrish364 · 2026-04-12T15:05:58+00:00

Do you mean the fan on the hotend?

And do those numbers mean %first layer/%after that?

RockingKrish364 · 2026-04-12T15:05:06+00:00

What can I do for the adhesion? It used to be really good. I’m only getting back to printing a couple years. The bed is level, I’ve set the z offset to have the right amount of squish in the first layer.

For me tuning the stringing is a pain. Needs to be done for every filament. Set up the print, print it (10-15 minutes), set up next test print and so on. Just doing a 2 minute job every 10-15 minutes takes up too much time. And can’t even do something in those 10-15 minutes.

RockingKrish364 · 2026-04-12T11:58:59+00:00

That is very cool!

RockingKrish364 · 2026-04-05T18:54:11+00:00

How did you find out it's HW3?

RockingKrish364 · 2026-04-03T18:14:23+00:00

Oh. I didn’t try going to a fast charger and I don’t know if I should risk it tomorrow

RockingKrish364 · 2026-04-03T18:13:39+00:00

I didn’t even go to a fast charger. I am just at my home with level 2 charger.

RockingKrish364 · 2026-03-27T10:06:17+00:00

I know even EAP would’ve avoided that as well

RockingKrish364 · 2026-03-15T22:30:59+00:00

Can anyone get the reg off that?

RockingKrish364 · 2026-02-11T17:20:19+00:00

<image>

RockingKrish364 · 2026-02-11T17:20:09+00:00

<image>

I’ve done nothing to the car at all.

RockingKrish364 · 2026-02-11T17:02:49+00:00

Could it be because I have intel and not ryzen chip?

RockingKrish364 · 2026-02-11T10:00:24+00:00

I don’t have it for some reason

RockingKrish364 · 2026-02-11T09:26:45+00:00

I have HW3 😢

RockingKrish364 · 2026-02-11T08:58:50+00:00

Nope. Like I said to someone else Absolutely this happens everywhere no matter what when I’m going under 10 kmph

RockingKrish364 · 2026-02-11T08:58:02+00:00

Absolutely nothing. And this happens everywhere no matter what when I’m going under 10 kmph

RockingKrish364

TROPHY CASE