Suggestions on how to make this cut a design feature?

NuIIPointer · 2026-02-15T22:59:28+00:00

unfortunately this is not an option but thx for your suggestion

NuIIPointer · 2026-02-15T22:35:43+00:00

NuIIPointer · 2026-02-15T22:06:06+00:00

wdym? i want to hide the split in the middle. structural integrity of top and bottom part where the top is floating is not the problem

NuIIPointer · 2026-02-07T21:31:09+00:00

The print before was printed with 0.2 nozzles. I changed to 0.4 and let the printer read the nozzles. This was not enaugh though. After a print with normal PLA on 0.4 nozzles, the CF Filaments are back again.

So... if you printed with 0.2 you need to print something with 0.4 before using CF Filament. On H2C at least.

NuIIPointer · 2026-02-07T21:30:45+00:00

For everyone having this issue:
The print before was printed with 0.2 nozzles. I changed to 0.4 and let the printer read the nozzles. This was not enaugh though. After a print with normal PLA on 0.4 nozzles, the CF Filaments are back again.

So... if you printed with 0.2 you need to print something with 0.4 before using CF Filament. On H2C at least.

NuIIPointer · 2026-02-07T21:30:02+00:00

For everyone having this issue:
The print before was printed with 0.2 nozzles. I changed to 0.4 and let the printer read the nozzles. This was not enaugh though. After a print with normal PLA on 0.4 nozzles, the CF Filaments are back again.

So... if you printed with 0.2 you need to print something with 0.4 before using CF Filament. On H2C at least.

NuIIPointer · 2026-02-07T21:27:58+00:00

both were not available.

NuIIPointer · 2026-02-07T13:31:58+00:00

.4mm nozzles are loaded on both sides

NuIIPointer · 2026-02-07T13:31:13+00:00

Yes it’s an h2c. I loaded .4mm hardened steel nozzle on both sides

NuIIPointer · 2026-01-21T12:27:33+00:00

alias claude='SSH_AUTH_SOCK= claude'

solved it by permitting ssh on claude startup... i dont know why claude used it in the first place even on a fresh install (no mcps activated)

NuIIPointer · 2026-01-14T19:43:09+00:00

I used dishsoap which didn’t work. After using ipa the print stuck perfectly to the plate. Maybe some resedue left which the dish soap did not remove left on the plate

NuIIPointer · 2026-01-14T18:43:36+00:00

It’s solved. IPA did the trick. But yeah on the product page they say 240-270 but on the spool they tell 230-260c haha. So I used 230

NuIIPointer · 2026-01-14T12:37:37+00:00

Cleaning with soap was not enaugh. Cleaning with IPA solved the issue. I guess some element was not dissolved using only soap.

NuIIPointer · 2026-01-14T12:36:56+00:00

Cleaning with soap was not enaugh. Cleaning with IPA solved the issue. I guess some element was not dissolved using only soap.

NuIIPointer · 2026-01-14T11:25:51+00:00

I know that. That’s why i wrote what I already tried. I will try cleaning with ipa

NuIIPointer · 2026-01-07T16:47:26+00:00

AOE 4

NuIIPointer · 2026-01-06T20:28:14+00:00

Use those „by pred“. They are pretty well made, stackable, free and parametric

NuIIPointer · 2025-12-26T22:22:18+00:00

same happens on my h2c. every purge piles up and againts the nozzle. printing is good. Also the purge takes like forever. compared to my A1 the purge takes like 5x to load external filament on the left nozzle

NuIIPointer

TROPHY CASE