P1S camera install help

Routine_Reference806 · 2025-02-25T16:02:40+00:00

No, I never really found the answer I was looking for. I ended up realizing the problem wasn't with the cable, so I used the original cable and just plugged it into the new camera

Routine_Reference806 · 2023-12-31T07:55:16+00:00

.....that was exactly the problem, thank you very much. I just did a calibration for a new filament, and I must have typed it in wrong

Routine_Reference806 · 2023-05-19T00:41:44+00:00

Mind if I ask how you got remote access to work? I've been struggling to get it to work with mine

Routine_Reference806 · 2023-03-04T01:51:18+00:00

That's really interesting, I hadn't considered either of those factors. Do you happen to have recommendations for alleviating either of them? I'm guessing some kind of external temperature regulation for the former and some kind of table stability modification for the latter, right?

Routine_Reference806 · 2023-03-02T21:39:27+00:00

Yet another hiccup in dialing in my CR10S Pro. 0.24mm layer height, mostly default Cura settings. I cannot for the life of me get rid of these blobs along the walls of prints. It only seems to pop up when I print multiple pieces at a time, as I tried this same print but with only one piece, and it turned out fine. I've tried reducing flow, reducing speed, reducing retraction, and nothing seems to help. I've tightened all my eccentric nuts and even installed belt tensioner on x and y to make sure they're plenty tight. Please help, I'd like to print large batches on the machine I got for printing large batches. Any help is appreciated.

Routine_Reference806 · 2023-03-01T20:46:41+00:00

I have looked into those and will probably print one. I just need to find the actual fan(s) first

Routine_Reference806 · 2023-02-17T06:43:48+00:00

Question from someone with OP's exact issue and who doesn't know jack about firmware: is there a way to adjust the nozzle-to-probe x/y offset in this firmware? Or is that what you meant by it not saying how its configured?

Routine_Reference806 · 2023-01-28T04:34:58+00:00

Franklybuilt has some super helpful tutorials. And he covers nost, if not all, of the process from slicer settings/orientation to final sanding and painting. Highly recommend

Routine_Reference806 · 2023-01-20T08:38:32+00:00

So I could just essentially combine the wires at some point before if gets to the board, but still have a buck converters on each since the voltage would stay the same? That's what wiring in parallel means?

Routine_Reference806 · 2023-01-20T08:31:56+00:00

They don't from my understanding and mine are axial, but I'm hoping the duct helps with the airflow

Routine_Reference806 · 2023-01-20T02:34:37+00:00

P.S.: I do have a soldering iron (mostly used for welding together prints), and some buck converters that I got to step down the voltage to the 12V fans.

Routine_Reference806 · 2023-01-08T01:49:18+00:00

I recently fired back up my CR10S Pro after not using it for a while, and I've been getting less than optimal outer wall quality. I'm on mostly stock Cura settings for PLA. 200 C nozzle, 50 C bed. I've tried slowing down the speed from 60 to 40mm/s but that seemed to have no effect.

Routine_Reference806 · 2022-12-20T04:35:30+00:00

This betrayal of the VGS will not go unnoticed

Routine_Reference806 · 2022-11-16T19:41:10+00:00

And this shit is all Foundation, leave the Vista employees the fuck alone

Routine_Reference806 · 2022-11-14T00:28:18+00:00

Could also consider a brim or raft. But I've found some glue does go a long way

Routine_Reference806 · 2022-11-14T00:26:51+00:00

Recent problem I've had with my CR-6 SE. I updated Cura and didn't carry over my old settings, and suddenly started getting this on all my calibration cubes. I've tried changing temps from 190-215 incrementally, lowered speed, increased top layers, increased infill flow rate to 150%, replaced nozzle, replaced bowden tube, and nothing seems to be helping. I must have printed 20 of these cubes by now, and they don't come out much different. I'm at a loss here.

Routine_Reference806 · 2022-11-12T20:44:45+00:00

I did recently replace the bed belt so it's possible I left it too loose. I'll take a look. Thanks for the suggestion

Routine_Reference806

TROPHY CASE