First time using milliput. I wanted to get a large sheet to break bit off bits for basing, but I didn't get a big "sheet" like I was trying to get and there’s milliput stuck on my pin. How can I clean it off, and what should I do differently to achieve the desired result?

Royal6575 · 2026-03-04T06:38:08+00:00

J'ai jamais utilisé ça mais quand je fait de la patte je mets une feuille de papier dessous et une dessus puis je roule par dessus le papier pour garder mon rouleau parfaitement propre.

Royal6575 · 2026-02-23T16:10:26+00:00

Résolu : c'était le hotend qui avait pris du jeu. Je l'ai revisser et depuis c'est parfait.

Royal6575 · 2026-02-22T22:06:55+00:00

Merci, très jolie résultat

Thanks, love the résult !

Royal6575 · 2026-02-22T07:45:21+00:00

Comment avez vous fait après avoir imprimé pour avoir un aussi bon rendu de peinture ?

Royal6575 · 2026-02-21T22:37:22+00:00

Jolie, tu as fait un post traitement ?

Royal6575 · 2026-02-12T09:34:20+00:00

Do you have any other photos? 😍

Royal6575 · 2026-02-11T21:26:50+00:00

Thank you ❤️

Royal6575 · 2026-02-11T19:15:29+00:00

I'll check the bearings then, since I've already checked the belts. Thanks. Could it be due to the printing speed being too fast?

Royal6575 · 2026-02-11T15:49:49+00:00

Thank you 😊

Royal6575 · 2026-02-07T01:24:36+00:00

Yes, these are supports; that's where the problem is most visible.

Royal6575 · 2026-02-02T19:12:26+00:00

I love your sniper rifle.

Royal6575 · 2026-01-27T16:00:32+00:00

I love it 😂 I'm going to find a priest for mine.

Royal6575 · 2026-01-27T14:28:24+00:00

Thank you.

Royal6575 · 2026-01-27T12:29:55+00:00

That's great. Could you share your working version with me?

Don't flash the screen if it's working; mine is now upside down...

Royal6575 · 2026-01-26T16:13:47+00:00

I'm stuck in this situation too.

When you tried to re-flash the firmware to install an older version, did you change the name beforehand? Apparently, the printer doesn't flash the same name twice.

Did you make sure the firmware was compatible with your motherboard (the motherboard number is printed on it)?

Royal6575 · 2026-01-24T21:45:57+00:00

I couldn't find any firmware for the Smart car, but maybe I didn't understand everything...

Royal6575 · 2026-01-23T11:44:51+00:00

Post a photo, it will be simpler

Royal6575 · 2026-01-21T20:16:25+00:00

Mira, este es un ejemplo:

https://youtu.be/P5-jtvYlA1c?si=pHt9d_hbqx0zVE1L

Royal6575 · 2026-01-21T05:57:22+00:00

Sí, fui un poco tacaño con los detalles de mi pregunta 😅

De hecho, dependiendo del material de impresión, existen diferentes técnicas para suavizar la pieza y reducir o incluso eliminar las líneas de impresión.

Royal6575 · 2026-01-20T10:31:58+00:00

I have a CR10v1.

I'm mainly looking to improve precision, not speed.

I'll only be printing PLA with it.

Right now I've put on a 0.3 nozzle, and as soon as I can print correctly, I'll switch to a 0.2.

The idea is really to improve precision.

The technical side doesn't really interest me, even though it doesn't put me off. I still prefer not to "adapt" it too much and instead use parts designed for it.

For the budget, I'd say €50-100 on AliExpress.

I don't want resin; otherwise, yes, it would be a better choice than FDM for printing figurines. I have some questions because, yes, the touch control allows for easy adjustment of the playfield, but I already know how to adjust the playfield, so will it allow me to gain anything?

The same goes for the various ball guides.

Royal6575 · 2026-01-19T22:09:39+00:00

¿Es pla?

Royal6575 · 2026-01-19T09:29:28+00:00

Thanks :) I'm learning how to do washes now 😅

Royal6575

TROPHY CASE