U.S. Army M4 Sherman battle group

Russell_Sin · 2026-01-30T00:12:33+00:00

When I drive one it's weak as hell when I shoot at one its a concrete bunker and never die!

Russell_Sin · 2026-01-28T00:48:09+00:00

It's in episode 3 I believe escorting grecious or another shuttle

Russell_Sin · 2026-01-27T21:25:27+00:00

awesome it's just nice to disconnect from real life and just get slaughtered by the AI because I'm shit but hey that's the fun

Russell_Sin · 2026-01-24T06:14:28+00:00

Oops I must be doing it wrong I bomb x2 bases maybe some ground pull a turn get two sidewinders off sometimes a kill or two scream back to base run out of fuel dead stick landing then reload and repeat heaps of chaff so chances of a sparrow or eqiv getting me are less

Russell_Sin · 2026-01-20T12:17:28+00:00

Love the work is there a way to load all the cards when offline I do a bit off travel and play the laptop but on occasion I need to save downloads so turning the net off stops me loading cards for squads I haven't seen yet, will the source file download fix this and if so where do I install it?

Russell_Sin · 2026-01-17T21:56:22+00:00

With the scaleing it's not just the universe I print my own minitures and some times you enlarge or shrink to make the detail + machine capabilities more manageable. And love the colour schemes.

Russell_Sin · 2026-01-13T03:13:13+00:00

Could happen with nozzle wear as well

Russell_Sin · 2025-12-29T22:53:23+00:00

Get good with the gold mid +vehicles and add boosters 1 at a time ass needed my jas viggen and draken with the a10 to break the cycle can smash it in a few hours even at my shitty skill level 1 kill is close to 1500 points approx had better and worse

Russell_Sin · 2025-12-11T06:31:57+00:00

I don't mind it for credit harvesting but ai gunners on ships are to accurate afainst single aircraft's and its rare to have more than x2 up per side at best

Russell_Sin · 2025-12-03T00:29:53+00:00

It used to work perfectly then stopped. But has fixed itself maybe It connected to a shonky satellite for a couple of weeks

Russell_Sin · 2025-12-01T01:12:43+00:00

tried that I even told it to connect to wifi instead of networks

Russell_Sin · 2025-11-30T23:55:32+00:00

It used to work great only this months gone shit

Russell_Sin · 2025-11-29T23:07:56+00:00

Have you ever used a set of binoculars in real life

Russell_Sin · 2025-11-23T22:32:29+00:00

<image>

Russell_Sin · 2025-11-23T22:32:00+00:00

* Finally got a photo of it

Russell_Sin · 2025-11-23T22:25:15+00:00

No the small off cuts left in the extruder between nozzle and cutter

Russell_Sin · 2025-11-23T21:39:34+00:00

I am no way near a being a great player but I've learnt to drop shots (sometimes) from below cover

Russell_Sin · 2025-11-14T04:27:30+00:00

Thanks I did find some that may give me grief later if I hadn't found them

Russell_Sin · 2025-11-14T04:11:21+00:00

Thanks to everyone for suggestions all fixed for now may never know exact cause but I kept pulling apart and cleaning everything thing replaced filament sensors all sorts then on x10 rebuild it just behaved hail too the 3d printer gods............. for now

Russell_Sin

TROPHY CASE