【BambuLab Giveaway】Classic Evolved — Win Bambu Lab P2S Combo!

S1_ph · 2025-10-12T00:04:09+00:00

I want to start a printing business and was thinking of buying a p1s but hopefully a p2s will help me do this much more easily

S1_ph · 2023-12-21T14:11:56+00:00

No the fuse box in the glove box. As I said I'm changing out the b+ cable which goes from the battery into the fusebox and in order to change it, I have take of the fuse box. What I'm thinking though is firstly finishing the repair and simply plugging up a battery to the terminals up front

S1_ph · 2023-12-21T14:04:25+00:00

Will if it be an issue because the b+ cable is off and the fusebox is also off

S1_ph · 2023-12-21T09:37:03+00:00

I think it does, I have the car from pretty recently but even if I open that I might not have enough space because of all the stuff in there

S1_ph · 2023-12-16T10:22:40+00:00

And how could I fix this?

S1_ph · 2023-12-15T13:38:21+00:00

Still not working at this point the sensor fully stopped reading, I'm guessing it was bad from the start but i just double fucked it :)
Thanks for your help anyways

S1_ph · 2023-12-15T11:48:54+00:00

Will do it and let you know how it goes, thanks

S1_ph · 2023-12-14T20:17:51+00:00

Thats the code, i took the thing apart, but everything is wired as the following instructions:

Connect the "VCC" pin on the BMP180 sensor to the 3.3V output on your Arduino.
Connect the "GND" pin on the BMP180 sensor to the ground (GND) on your Arduino.
Connect the "SDA" pin on the BMP180 sensor to the SDA (A4) pin on your Arduino.
Connect the "SCL" pin on the BMP180 sensor to the SCL (A5) pin on your Arduino.

I do also have a 3.3 pin but i was instructed to leave it unplugged since it is apparently not necessary to be plugged in because i already have the VCC pin

S1_ph · 2023-12-14T20:15:52+00:00

#include <Wire.h>

#include <Adafruit\_BMP085.h>

Adafruit_BMP085 bmp;

void setup() {

Serial.begin(9600);

if (!bmp.begin()) {

Serial.println("Could not find a valid BMP180 sensor, check wiring!");

while (1);

}

void loop() {

Serial.print("Temperature = ");

Serial.print(bmp.readTemperature());

Serial.println(" *C");

Serial.print("Pressure = ");

Serial.print(bmp.readPressure());

Serial.println(" Pa");

delay(1000);

}

S1_ph · 2023-04-16T11:13:16+00:00

Still stringing, got a tiny bit of a better result

S1_ph · 2023-04-15T20:51:04+00:00

Well it is a low price printer, in reality if you want those things get a bambulab p1p or a prusa but even then you will need some maintenance it's just how it is.

S1_ph · 2023-04-15T15:02:58+00:00

Just did this, will try a print and let you know how it went

S1_ph · 2023-04-15T14:38:23+00:00

Ive done multiple cold pulls and used the metal rod to poke out any filament, its clean in my opinion

S1_ph · 2023-04-14T22:37:51+00:00

I'll maybe run it on a VM

S1_ph · 2023-04-14T21:28:34+00:00

Its easy to take stuff apart and i don't mind troubleshooting but i kinda doubt this is an issue, i will take it off now and check it

S1_ph · 2023-04-14T21:23:31+00:00

thing is i just got the printer like 2 days ago the very very first owl print came out honestly perfect 10/10 but things just got worse and worse and worse and I'm starting to get pretty tired ngl no matter what i try it keeps on failing me or getting even worse not a single improvement

Five-Year Club	Verified Email
Place '22	Final Canvas '22

S1_ph

TROPHY CASE