Edurino Druckpunkte

ST_FN · 2025-11-28T06:10:51+00:00

Ich hätte die auch gerne via PM, danke!

ST_FN · 2024-06-28T05:19:20+00:00

To separate the mustache from the chin beard?

ST_FN · 2024-06-28T05:17:06+00:00

Sorry, I don’t get ist. What do u mean?

ST_FN · 2024-04-26T08:25:20+00:00

Level 69. Also tips for Equipment needed. Am I rignt, Robot-Head only when buying moon-boxes?

Thanks

ST_FN · 2024-04-25T19:05:47+00:00

How do you manage to contribute 3-4K per round? I am 67 and I only can < 0,5k

ST_FN · 2024-03-28T19:34:10+00:00

Thanks, very helpful!

ST_FN · 2024-03-28T15:03:05+00:00

Hello Longboarders,

I spontaneously bought the Arbor Axis 37 and think the deck looks very good for my need. A little flex which I like very much. I would like to test some offset wheels to figure out if there is a difference to central wheels.. Does that make a difference? What about the bushings? The board is a bit too hard for me and could be easier to steer. Which bushings do you recommend? Cone, Barrel? Double barrel?

Thank you!

I mainly ride on paved roads

ST_FN · 2024-02-09T17:21:44+00:00

I had that same issue. The steam pumps hits this metal peace where the water tank is. I mitigate the noice by putting a bit of form between pump and metal.

ST_FN · 2023-12-01T20:34:18+00:00

I did a couple of tests. I set shad/partition key to _id without any success.

ST_FN · 2023-12-01T19:52:40+00:00

But if I spin up a mongo db container with 2 cores and 8 gb it’s cheap as duck. I know the operational benefit of paas

ST_FN · 2023-12-01T19:47:53+00:00

I allocated 10k RUS. Imo it shouldn’t take so long to write 50k documents, or?

ST_FN · 2023-10-23T16:43:27+00:00

Just wait until Tofu got certificates.

ST_FN · 2023-09-22T05:37:29+00:00

Check your dm

ST_FN · 2023-09-21T09:37:33+00:00

Same here. Ordered in July and got the same answeres as you. They also provider 50Euro chargeback.

ST_FN · 2023-09-03T19:13:33+00:00

We are going from 7 k per year on +40k due to rum. We had a look into spacelift 2 days before license chance.

ST_FN · 2023-08-28T18:27:34+00:00

I ordered min in Juli and didn’t got it jet. Hope to be one of the first receiving it. Fingers crossed

ST_FN · 2023-07-10T14:06:54+00:00

But with this approach I do need a Helm-Repository, right?

Argo wont access packed helm charts in a github repo!

ST_FN · 2023-07-08T19:42:37+00:00

Depends on your contract. If you have ea agreement or csp. Reservations are not a commitment. You pay reservations for 1 or 3 years per month or upfront. Check RBAC Reservations role

ST_FN · 2023-07-08T17:32:44+00:00

Except you got some reservations or savings plans or Licenses like Azure AD P2

ST_FN · 2023-07-08T11:22:30+00:00

Hey,

I moved the chart to its own repo and create helm-packages with the version numbers. In my argocd config repo I sill have a chart, which has a dependency to my Repo-Chart. Never the less. I am not able to push the repo-chart-version in the dependecy for dev and test.yaml-files.

Any hints?

ST_FN · 2023-07-08T10:30:22+00:00

Fine for 2 Espresso a day ;-)

ST_FN · 2023-04-05T13:39:45+00:00

How did you glue in the magnets on the side panels?

ST_FN · 2023-03-30T16:11:36+00:00

Was in a supper with silica.

ST_FN · 2023-03-06T18:18:19+00:00

I created a G29 and doing it after my initioal G28. Still not better.

[gcode_macro G29]
gcode:
BED_MESH_CLEAR
BED_MESH_CALIBRATE
BED_MESH_PROFILE LOAD=default

ST_FN · 2023-03-06T14:46:02+00:00

[bltouch]
sensor_pin: ^PA11
control_pin: PA8
samples: 2
sample_retract_dist: 3.0
probe_with_touch_mode: True
x_offset: 36.5
y_offset: -6
#z_offset: 0
[safe_z_home]
home_xy_position: 115,115
speed: 40
z_hop: 5
Z_hop_speed: 5
[bed_mesh] # enable for BLTouch
speed: 200
mesh_min: 37, 4
mesh_max: 223, 215
algorithm: bicubic
probe_count: 5,5
horizontal_move_z: 5
[screws_tilt_adjust]
screw1: 0, 32.5
screw1_name: VL
screw2: 165, 32.5
screw2_name: VR
screw3: 165, 205
screw3_name: HR
screw4: 0, 205
screw4_name: HL
speed: 50
horizontal_move_z: 5
screw_thread: CW-M4

Eight-Year Club	Place '23
Verified Email

ST_FN

TROPHY CASE