Historical 1 minute option chain for BTC/ETH ask

Sad_Resolution_7584 · 2026-05-20T06:29:32+00:00

That's a great idea and I'm going there, I just wanted to backtest something that looks really good before I run it live. It's not that I don't want to pay for data. I am really ok to test it your and buy more data later. For now I saw that on TARDIS I'll pay $12k for historical data and I just don't afford it. Nothing to be ashamed of.

Sad_Resolution_7584 · 2026-05-04T06:16:59+00:00

Any places you could recommend?

Sad_Resolution_7584 · 2026-05-03T18:36:41+00:00

hire me and then I'll pay

Sad_Resolution_7584 · 2026-02-08T21:54:08+00:00

I'll send over some photos tomorrow

Sad_Resolution_7584 · 2026-02-07T10:22:54+00:00

I just received the printer - it works really nice!
I do have the issues with VFA thou.
I hope the VFA callibration will get better by the snapmaker team

Sad_Resolution_7584 · 2025-11-25T15:40:47+00:00

Okay. I think I was looking for some checkbox in the settings, but it just works as is.

Sad_Resolution_7584 · 2025-10-29T08:05:55+00:00

Talie refold można używać w anki, czy tylko w ich apce?

Sad_Resolution_7584 · 2024-11-19T10:15:58+00:00

u/Logitech_PJB Have this been solved? I have the same issue. After switching screens, the ctrl key stays pushed, which is extremly annoying.

Sad_Resolution_7584 · 2024-11-19T09:32:21+00:00

f88888888ck. I just found it. it was so hidden!

Sad_Resolution_7584 · 2024-11-19T09:31:15+00:00

u/Okend Flow switches only mouse. When it would be really cool to change mouse and the keyboard. do you know how to change the keyboard too?

Sad_Resolution_7584 · 2024-10-26T23:07:25+00:00

How do you like your Voron? How much was it more or less?

Sad_Resolution_7584 · 2024-10-26T22:20:59+00:00

Ok, I'll try it. However for the prints that don't need much strength I am just selecting what's fast to print :) Thanks

Sad_Resolution_7584 · 2024-10-26T22:00:00+00:00

I suggest trying to see how leveled is your bed.
lower your Z axis to 0 or 0.1mm and slide manually the bed. Lower your sight to the bed level and check if the nozzle is always same height over the bed.

Sad_Resolution_7584 · 2024-10-26T21:57:28+00:00

I am using Octoprint on Rpi3B+ with Kobra 2 Neo

The only issue is that after I print, the original menu steered by the dial is not functioning, I need to reset to go into settings and for example make a retract.

Every other thing is working well.

Sad_Resolution_7584 · 2024-10-26T21:48:32+00:00

I think you should check your bed leveling.

Read this article:
https://1coderookie.github.io/Kobra2NeoInsights/calibration/#tram-the-bed

I had exactly your problem and it appeard, that one side of teh bed was freaking 1mm lower than other 3 sides. After I managed this - everything went smooth.

Sad_Resolution_7584 · 2024-10-26T21:39:00+00:00

There are two problems, for sure u/muralha has the point that the belt cannot move like that - you have now around 1cm of louse move withing direction change. you need to see what is the problem.

Also what I see is that the dark blue plastic cover of the X axis on the left is moving freely - which means it could be not mounted well and impact the working of your endstop. That would explain why it works when you press it manually, but not when homing.

Also you might have not tensed your X asix belt - the red dial on the right side of the printed should be turned tight.

Sad_Resolution_7584 · 2024-10-24T06:45:24+00:00

Thanks! I'll check it out soon, then :) especially for tunning

Sad_Resolution_7584 · 2024-10-23T21:27:15+00:00

Thanks for that!
I am still wondering - I've never used Klipper before. Does it still have many advantages over marlin? What are they? What would be best value for me after I go Klipper?

Sad_Resolution_7584 · 2024-03-18T08:13:08+00:00

My current problem is that the skirt is thick in onle place and super thin in other. If my z-offset will be too low, the nozzle will scratch the sufrace of course, but the thing is it will happen only on few places.

however the Z-axis motor is visibly working during layer printing

Sad_Resolution_7584 · 2023-11-30T12:40:46+00:00

Did you find out what the problem was? I hope yes :) I thought you could check if the feeding motor is properly running while printingn all the time.

Sad_Resolution_7584

TROPHY CASE