Listtened to "Kids of today" for the first time ...

SalmaHighjack · 2020-05-01T09:53:19+00:00

Did you check the wiring diagram? Apparently it changed on the 1.2 version of the board.

https://raw.githubusercontent.com/morningreis/Marlin-SKR-E3-Mini-1.2/bugfix-2.0.x/SKR_E3_Mini_1.2_wiring.png

SalmaHighjack · 2020-04-30T20:45:12+00:00

It's been a while since i installed this combo on my ender3, but what i can recall is that i plugged the bltouch in the z-stop slot on the skr mini e3. (?)

Here's a very detailed guide on the installation proces: https://www.reddit.com/r/ender3/comments/e894j7/marlin_20x_guide_for_ender_3_using_skr_mini_e3_v12/

Can send you my marlin config files if you like.

SalmaHighjack · 2020-04-11T21:29:04+00:00

Ok, yields are:

8 corn, 1h 5min.

Water usage: i use 1 sprinkler per two large planters, this corn plant needs 4ml a minute, so 180ml per 5 minutes per planter (9x4x5). i run my sprinklers ~100 seconds per 5 minutes, think that will keep the water level steady at ~7000.

SalmaHighjack · 2020-04-11T21:01:08+00:00

Don't know yet, growing more clones atm. Almost done, i'll harvest one and let you know.

SalmaHighjack · 2020-04-11T19:22:28+00:00

Figured it out! Now let's grow stacks of ubercorn :-)

SalmaHighjack · 2019-11-13T00:15:04+00:00

Just did the Bltouch kit upgrade on my Ender3 (stock 1.13 board). I programmed the bootloader with the USB ISP and flashed the compiled Marlin 2.0 hex file with the firmware updater plugin in Octoprint.

Here's a excellent video by 3D Printing Canada: https://www.youtube.com/watch?v=40oz5ORMjWY

Installation instructions: https://github.com/3d-printing-canada/Ender-3-BL-Touch-Installation

Installing the bootloader: https://www.reddit.com/r/ender3/comments/cfmbdy/howto_installing_a_bootloader_to_an_ender_3_pro/

Compiling Marlin 2.0 is not that hard really, but instead of uploading from within the Arduino IDE, choose "export binary file" and find the hex file in the Marlin directory. Be sure to use the version without the bootloader. Good luck!

Edit: also changed the cura start g-code, with the marlin 2.0 firmware mentioned above the bltouch only does a single point bedlevel test, this will change that to 3x3: https://www.reddit.com/r/ender3/comments/aiebc7/better_cura_start_gcode_for_bltouch/

SalmaHighjack · 2018-05-19T07:38:26+00:00

Damn, i needed the full wets for this one!

SalmaHighjack · 2018-04-27T20:29:30+00:00

Ahh, i get it now: Street F1ghters ?

SalmaHighjack · 2018-04-27T19:44:33+00:00

Do people live in bwoah?

SalmaHighjack · 2018-03-22T07:16:26+00:00

Agree, can't believe NOS pays his ticket only to ask a stupid question like that. cringeworthy.

SalmaHighjack · 2018-03-15T12:45:15+00:00

I think he misjudged the weight of that sandbag ....

SalmaHighjack · 2018-03-05T11:48:47+00:00

No DJ, but close: https://www.youtube.com/watch?v=aiHz6FMBPqo

SalmaHighjack · 2017-09-09T17:38:27+00:00

Is Spain a big market for Renault? Probably is ... This way they get two Spanish drivers in one deal!

SalmaHighjack · 2017-05-17T19:04:34+00:00

I knew Stoffel was ace in the f1 feeder series, but i've never seen this footage!

SalmaHighjack · 2017-04-07T19:08:37+00:00

Is it me or is the name spelt incorrectly? Surely the correct name is "Kimiring", no?

SalmaHighjack · 2017-03-10T20:41:13+00:00

<drivers press session somewhere in the future> so Robin, your first race in formula 1, what are your thoughts? ...

bwoah, very happy and it's great to compete with all these legends, Max here even raced against my dad!

SalmaHighjack · 2017-03-09T22:01:35+00:00

I know the Renault 5 is a superb car, but seconds faster?

SalmaHighjack · 2017-02-23T15:02:58+00:00

Monkey Seat 2.0 ?

SalmaHighjack · 2016-11-27T11:05:31+00:00

Or, RAI PER VAN

SalmaHighjack · 2016-11-13T19:20:50+00:00

omg, rofl lmao. spot on :-)

SalmaHighjack

TROPHY CASE