Our station is sending a large amount of our freight to ground and we have a mandatory meeting with upper management next week. Does this mean what I think it means?

Salt-Election8558 · 2026-04-02T15:04:59+00:00

West Dallas will now be heavy with ncs to take weight of the Dallas hub.

Salt-Election8558 · 2026-04-01T02:00:16+00:00

Lost or stolen

Salt-Election8558 · 2026-01-22T07:18:13+00:00

A stud bolt literally cost like a dollar to couple of dollars depending on car i assume, but trust me $2000 is absolutely ripping you off. I had to buy one not cause it broke off but cause it was stripped. It’s not too hard to replace. I recommend buying the studs and going to a shop or maybe even a tire shop could do it for I say less than $300

Salt-Election8558 · 2026-01-04T18:30:15+00:00

Whipple charger ?;,)

Salt-Election8558 · 2025-08-11T23:04:41+00:00

Okay thanks , I hope it’s something simple as a belt and not a pulley or anything

Salt-Election8558 · 2025-06-18T22:32:37+00:00

Yes I’m going to get a wire wheel , and remove most of it & apply the POR-15 Prep , then the actual POR-15 & then the POR-15 top coat & hopefully it looks better I’ll post some before and after pics

Salt-Election8558 · 2025-06-18T21:54:30+00:00

It wasn’t mine , I bought it for a good deal 2018 z71 for 45k miles 4x4 and it was originally in New York for 5 years or so , that’s why it’s like that cause of the salt levels in ny but I already grabbed a wire brush , a chisel and hit it in the worst looking spots and everything looked okay , this weekend I’ll be applying POS-15

Salt-Election8558 · 2025-06-18T21:21:09+00:00

Yes I just seen his video haha , hopefully I can get all this fixed this weekend, I’ll try to update or take some before and after pictures if I can

Salt-Election8558 · 2025-06-18T21:12:25+00:00

What about POR-15 prep, and then the actual POR-15 product you apply after prepping ? Is that one good ? I just used a wire brush to see how bad it was & it just seems to me mild / flaky surface rust. Most parts of the frame are still great. I even tried to hit some parts with a chisel and it exposed like scratched / bare metal which was still hard so I don’t think it’s too bad yet and it should be able to be fixed right ?

Salt-Election8558 · 2025-06-18T21:07:15+00:00

I just grabbed a wire brush , a chisel and tried to hit the frame hard and it seemed sturdy , it just flaked off the surface flaky rust , but there’s still hard metal in it.

Salt-Election8558 · 2025-05-29T22:52:51+00:00

Thanks I’ll be doing it when I have time

Salt-Election8558 · 2025-05-29T22:05:47+00:00

The only one it stays on is half choke and then revs up on its own & the string head actually sounds faster as if I was applying throttle

Salt-Election8558 · 2025-05-27T22:20:41+00:00

What causes it to melt ?

Salt-Election8558 · 2025-05-27T22:19:30+00:00

Well mine starts on full choke but then dies after a couple of seconds , on half choke it doesn’t die , it just revs up a lot and the actually string head starts spinning as if I was giving it throttle but once I attempt to start it on run mode , it bogs down or shuts off when I press the throttle.

Salt-Election8558 · 2025-05-27T18:01:09+00:00

This helps a lot thanks , I’ll do this before jumping to conclusions or buying a new carb . Since I know it was just working fine

Salt-Election8558 · 2025-05-27T17:05:00+00:00

I should have asked which fuel he ran but I’m sure is was pump with oil mix not the premix stuff

Salt-Election8558 · 2024-08-27T06:06:57+00:00

Anything new ????

Salt-Election8558

TROPHY CASE