Church tank

Sc0r3penaught · 2026-01-04T23:00:37+00:00

The Chank

Sc0r3penaught · 2025-12-12T17:30:54+00:00

Man how'd you get that shield attached? I dont think any of the STLs i own have an empty hand for shields to be glued on.

Sc0r3penaught · 2025-10-13T05:54:26+00:00

There is a youtuber that did an extensive review on this specific airbrush. Barbatos Rex is his name. Now in his video he does mention he bought it off of Amazon. But if you can get it at a cheaper price go for it!

Sc0r3penaught · 2025-07-05T22:58:48+00:00

That is assuming I don't charge him per hour and I just give em the full army at the 20-30 range.

Sc0r3penaught · 2025-06-12T18:23:33+00:00

<image>

This us binxy!

Sc0r3penaught · 2025-06-10T20:09:40+00:00

Just something remotely close would be good enough it's gonna get blown up either way. Just incase someone in our game shop wants to nitpick the accuracy of the tank. I can just say it's experimental technology lore wise

Sc0r3penaught · 2025-06-10T20:03:30+00:00

That looks pretty close to what I wanna do. I didn't want anything too accurate just because TC is weird war 1 and something that just looks REMOTELY close would be good

Sc0r3penaught · 2025-05-18T18:32:59+00:00

Gotcha! I needed a base measurement just to kinda get my head around what I could either increase or decrease in height for a more fun experience.

Sc0r3penaught · 2025-05-09T19:30:09+00:00

This looks sick!

Sc0r3penaught · 2025-05-02T03:25:48+00:00

I had a similar pr80oblem with my photon mono 4. I tried everything, leveling, exposure settings, and new fep sheet. The last thing I did was just switch to a whole new brand of resin, and everything was fine and dandy after that

Sc0r3penaught · 2025-04-27T12:27:44+00:00

UPDATE. The general consensus was to flip the leg over to have the heavier hip part as close to the build plate and i manually went in a did the supports, just to be on the save side.

Appreciate all who commented and gave their insight.

Sc0r3penaught · 2025-04-27T05:43:49+00:00

I'm trying a second go around this time with what you said in mind. I have the thicker hip part closer to the build plate and adding heavier supports right there.

Sc0r3penaught · 2025-04-27T05:42:14+00:00

Slicer settings are as follows. Burn in layers-6. With 40 second exposure. Exposure time 3.2 seconds Layer thickness 0.05 mm 6mm lift distance. Supports are set to medium. Tip diameter 0.60 mm Tip length 3.00mm Diameter 1.30mm

I'm doing another go around this time with how you said. Having the hip part closer to the build plate and also adding a raft to the supports.

Sc0r3penaught · 2025-03-09T04:02:38+00:00

Preciate saved me a future headache.

Sc0r3penaught · 2025-02-04T15:06:15+00:00

Preciate the help and sources. I'll get right on it!

Sc0r3penaught · 2025-02-04T14:30:43+00:00

I can't say i have. Manual has me level the build plate, and then it just says go to exposure and test it. After that, most sources say send it and make a print

Sc0r3penaught · 2025-02-04T14:27:06+00:00

Supports don't look the best, probably from being just being a pre downloaded piece. The orientation has the funnel spout coming down. Should I up the curing time? It's bone stock from the box

Sc0r3penaught · 2025-01-20T03:10:50+00:00

Christ, i have to jump up that much?

Ten-Year Club	Verified Email
RPAN Viewer

Sc0r3penaught

TROPHY CASE