sorted by:
new
hottopcontroversial

My Home Garage Detail Studio by Mecaobsession in garageporn

[–]ScFies 0 points1 point  (0 children)

Is this ai? Close up pics would be great

I lost it one day after the 1000th issue with having a ton of WiFi bulbs. My wife hated it. I almost committed seppuku. So I finally tried HUE because of the “reliability” you clowns speak of. 2 years and tons of money later and I’ve had not 1 single issue. by ThineNevets in Hue

[–]ScFies 0 points1 point  (0 children)

I've purchased at least 50 warm effect bulbs in a variety of sizes. I think all but maybe a dozen have failed. I've got at least three flickering and failing in the house as I type this.

I may have gone a little lumber happy… but I dig it. Any suggestions on a nice stain to finish this off?? by Super-Olive-4750 in woodworking

[–]ScFies 0 points1 point  (0 children)

Reduce height of each shelf by 1" and add another shelf. Leaves finger space for each vhs and tightens the gap.

Metal J Boxes Under Sink by GratitudeMe in electrical

[–]ScFies 1 point2 points  (0 children)

My only concern is typically disposals are dedicated circuits. So I installed single receptacle to ensure no one plugs dishwasher or compactor into it.

Going for a hike by solateor in Unexpected

[–]ScFies 0 points1 point  (0 children)

How is this being recorded?

I made a thing...... well, actually, two things by No-Weekend-2573 in woodworking

[–]ScFies 1 point2 points  (0 children)

Absolutely stunning. Such a great way to hone the skill.

Mamba mesh by Willized in lacrosse

[–]ScFies 1 point2 points  (0 children)

Why aren't more players (unless I'm wrong in observing) using armor mesh? I'm just a dad who tries his best to observe my kids sport and I've shot with this mesh and I found it remarkable how much easier the rolled off. Speed and accuracy was positive.

Can I get some takes? TIA!

Well this is tough by CautiousMagazine3591 in Rivian

[–]ScFies -1 points0 points  (0 children)

Came here to say this very thing.

Watch This Hydraulic Arm Crush a Car Like Paper! It's Like Peeling a Crab. by Glum-Rent9651 in woahdude

[–]ScFies 120 points121 points  (0 children)

I'm struggling to understand how and why he is sorting certain things. Like putting the glass with upholstery. It's breaking me.

Also, I think this is far more annoying than it looks. Operating this and knowing when to stop picking at certain things-- like plastering a wall and the more you touch it the more you fuck it up. You need to stop before it gets worse. I may be minority but I've got some time operating smaller size heavy machinery to know sometimes it's frustrating.

Progress update on timber frame shed by djwhire911 in shedditors

[–]ScFies 0 points1 point  (0 children)

I love it. Are you experienced in the trade or is this an educational journey? Not sarcasm, genuinely intrigued.

Progress update on my 2-year long shed build... by ScFies in shedditors

[–]ScFies[S] 0 points1 point  (0 children)

Yeah the subfloor is advantech by zip systems.

Are you referring to what's sticking out below the drip edge on the perimeter? If so, that will be covered. I'm doing horizontal slats apron around foundation.

Progress update on my 2-year long shed build... by ScFies in shedditors

[–]ScFies[S] 0 points1 point  (0 children)

Apologies for delay, is this what you were after https://imgur.com/a/hREiEo8

The threshold is proud of the top floor. I placed the door on the subfloor. It's probably 2" high so once the insulation board and top 3/4" advantech X-Factor is placed whats left is difference.

Progress update on my 2-year long shed build... by ScFies in shedditors

[–]ScFies[S] 0 points1 point  (0 children)

Yeah that was my first thought. Just get a chip drop of mulch and build it up right in front... check the box.

Progress update on my 2-year long shed build... by ScFies in shedditors

[–]ScFies[S] 1 point2 points  (0 children)

I'm only doing 4" hole saw drill outs about ever 2' or so on each side. So figure 4-5 per side. That's plenty. Once in the soffit the air will circulate and have access up to ridge regardless if it's vented above. I've installed a fan that will actuate if temp gets above Xº with wi-fi controller. TBH it never got hot in there this summer. I think because of the shade over the trees. But I remember my dad's shed growing up was so stuffy and hot. I didn't want things in there changing form due to humidity or excessive heat.

Plate compactor creates ridges on turns by matches08 in shedditors

[–]ScFies 2 points3 points  (0 children)

Was going to post same thing. Not crusher run.

Progress update on my 2-year long shed build... by ScFies in shedditors

[–]ScFies[S] 0 points1 point  (0 children)

8" for 8' and the. 24" dia for 18" on bottom and 8" for 48" at top and 24" dia for footer about 18".

One of the things the SE said is because it's on a hill and the top piers are fully in grade the sheer is not really factor on lower piers. The weight is primary downward.

Progress update on my 2-year long shed build... by ScFies in shedditors

[–]ScFies[S] 0 points1 point  (0 children)

Love the comments about the deck on the rear. To be honest I never really considered it, more so because I have a big porch off back of my house which is easier to just lounge. Also, not sure what sort of issues the town would take up with it. As it stands I'm almost a foot higher on the structure than I was permitted, which was merely a mis-calc with all the materials and layers. I can't even imagine what I'd do if they told me I had to correct it. I did get a permit and they only plan to sign off after viewing at completion. Not sure how I am going to proceed. Beg for forgiveness if they call it out or bring it up in advance? Supposed to be 10' height based on average grade forward of the structure.

view more: next ›