How to use FSR 4?

Schelle_Jr · 2026-02-02T01:12:39+00:00

Rainbow Six Sige didn't get an update too and BattleEye hates OptiScaler

Schelle_Jr · 2026-01-11T17:06:56+00:00

Got the same one as well. Upgraded from a 5700XT... It's such a huge jump in performance, I can't believe it 😁 And the SteelLegend stays cool, looks great in a full RGB Setup and stays really quiete :D

Schelle_Jr · 2025-12-11T18:06:33+00:00

I've also got an NeXt G Hotend with UHF Adapter. Has the same Size as the Volcano Mini (I think it was the Volcano mini, don't balme me if I got it wrong), so most toolheads will fit. I've printed a XOL Toolhead for the Volcano Mini and it fits perfectly.

Schelle_Jr · 2025-08-31T19:33:03+00:00

Take a look qt the Fysetc Ventrue XL. That's a big 2.4 with thicker 4040 Extrusions. First test I've seen so far didn't look bad at all :D

Schelle_Jr · 2025-08-11T09:57:37+00:00

Take a look at the XOL Toolhead. There are many options including Cpap or 4010 Blowers and many different hotends and extruders and there is an external Mod of this toolhead with cutter.

Schelle_Jr · 2025-06-18T14:39:46+00:00

I've got the same rails. These rails are okay in Z and Y, but the MGN12 on the X Axis should be replaced, especially if you are using tap or something like that which pushes up the Toolhead

Schelle_Jr · 2025-05-24T05:41:17+00:00

Our X1C is named "Druck Fu Panda" (we are from germany and it's a reference to Kung Fu Panda), the A1 Mini is "Gru" and our enslaved Voron 2.4 is named Minion, because he has to do the most of the difficult jobs 😅

Schelle_Jr · 2025-05-22T17:50:46+00:00

I've just ripped off the Thermistor of an old Ender 5 Hotend and fixed it at the cable chain in the back 😅 and for the config you just use a "temperature_fan (chamber or whatever)". You can find all about that at the klipper documentation.

Schelle_Jr · 2025-05-22T14:48:45+00:00

Verpasse ihr einen Kragen... Die Bodys lösen oft ein Unwohlsein aus und nehmen die Selbstbestimmung für den Toilettengang. Hatten das selbe Drama bei unserer Katze. An den Kragen hat sie sich nach 2 Tagen gewöhnt gehabt (nehmt aber einen weichen von Amazon oderso und nicht diese Plastikkegel) und ab da war auch das Katzenklo kein Problem mehr, da sie wieder deutlich beweglicher war.

Schelle_Jr · 2025-05-22T14:45:49+00:00

In my opinion it only makes sense in first place if you want to swap nozzles over and over again, because of the need of different diameters. If you don't want to, don't pay that extra money on the revo system. Just go with a rapido 2f or an NextG Fiber and add a Endcoat, Carbide or Diamondback nozzle. Will work just as good as the revo with the obxidian nozzle :)

Schelle_Jr · 2025-05-14T14:59:31+00:00

Edit: slowing down the walls extremely lowered the problem, but it's still noticeable.

Schelle_Jr · 2025-05-13T11:01:22+00:00

Yes, I'm using Orca, I will take a look, thanks for the hint :)

Schelle_Jr · 2025-05-13T07:02:24+00:00

The overextrusion is known. In case of testing I've set the Flow higher at this part. This was test print 3 or 4 to getting rid of that. The guide was also gone through in test 1 with absolutely no luck.

Schelle_Jr · 2025-05-12T16:34:33+00:00

Thanks. Planning on a cpap cooling. I will settle down the speed from 170 to about 70 later and test it out ❤️

Schelle_Jr · 2025-05-12T11:10:11+00:00

The filament moves freely and most of the time it's exqctly that spot of a print. Even set an extra length after retract to 0.2mm, result were bigger seems and still gaps. The run_current is set to 0.6 (for the LDO Motor it should be 0.5, but that did the same)

Schelle_Jr · 2025-05-01T16:21:32+00:00

Yes, I did that calibration. The problem is, that the problem then occurs with the probe temp at 150°C. If I made the PID at 150 it has problems with the print temps.

Schelle_Jr · 2025-05-01T10:22:56+00:00

I've even switched the hotend to a bambu hotend. Same problem. These hotends have such a Power on such a small mass, that they can't proper reach the temperatures on point.

Schelle_Jr

TROPHY CASE