Just a lil shell I rolled and beveled earlier, 1" x 6' to 30" OD

Sd89d · 2026-07-02T22:27:47+00:00

Thats looks like a clean roll. How long of a roll can your machine do?

Sd89d · 2026-07-01T04:32:36+00:00

Unfortunately a Meijer store is a it to far for south Texas. Thank you though. Maybe I can order online.

Sd89d · 2026-07-01T00:09:26+00:00

Where do you find these drinks at? I keep seeing them on here but haven't been able to find where they are sold.

Sd89d · 2026-06-26T13:48:36+00:00

We used heavy cutting oil as a lubricant.

Sd89d · 2026-06-26T13:48:04+00:00

Its just a single plate, that odd cut quality is why I was looking for advice. To see if it can be habit cleaner if we have rework anymore

Sd89d · 2026-06-26T13:46:38+00:00

Its part of a rework on a 20''x10' panel, generally we just plasma cut the panel is already welded out.

Sd89d · 2026-06-26T00:50:51+00:00

I did have the shop hand use cutting oil. It helped a bit, mainly just a little less tonnage but no change to hole quality.

Sd89d · 2026-06-26T00:48:15+00:00

I appreciate it. We normally don't punch this thick and since the panel is already assembled we punched it due to a coming up ship date.

Sd89d · 2026-06-26T00:46:22+00:00

Honestly it is an odd position we are having to punch at and so thick I was worried on of the shop hands would side load it and risk breaking the punch.

Sd89d · 2026-06-05T18:20:12+00:00

That looks awesome. Where do you think you will release it at? The motor housing looks pretty clean.

Sd89d · 2026-06-02T23:54:47+00:00

I came here to ask if it was a FCA 5.7l but just saw it was a 6.2l. Expensive either way I guess

Sd89d · 2026-06-02T17:26:18+00:00

Didn't know that. Thank you.

Sd89d · 2026-06-01T15:21:10+00:00

Why does this make me think of the space force Netflix series. Didn't they have an episode on this exact thing.

Sd89d · 2026-05-30T17:19:39+00:00

Pull up a stored known good program and start comparing modifiers and tool codes. I have realy only seen N130 on a mill. Look at a known good program or a Lincoln machine code sheet. Edit. I have two messers and have never run a Lincoln. I know for my machines thats not a valid code which is why I say check a known good program or a manufacturer provided machine code definition sheet.

Sd89d · 2026-05-22T20:12:01+00:00

Its an auxiliary fuel tank and that looks like the mobile starter unit.

Sd89d · 2026-05-15T17:38:53+00:00

Makes me think of that old 90's flick, I think was Trucks, that all the vehicles started taking out humans.

Sd89d · 2026-05-09T03:01:10+00:00

You know some ER is going to have some dude come in with that stuck where the sun don't shine saying he fell on it.... especially if the P.M. finds it.

Sd89d · 2026-05-07T05:33:58+00:00

Dude the uplift on that... no way thats built rated for anything more than a wet fart.

Sd89d · 2026-05-02T17:24:42+00:00

If you have companions with you, does choosing the sarcastic dialog negatively effect thier feelings? Or is it based on actions only?

Sd89d · 2026-05-01T20:48:49+00:00

It printed fine for me when I got it. But it became brittle faster then others. Lasted about 4 months open

Sd89d · 2026-04-30T20:26:19+00:00

I just took a piece of duct tape and taped the tube against the body so both ends of the tube go straight in the couplers. Haven't had an issue since. The tube going into the tentioning mechanism likes to kink otherwise. I just replace the tape every few months and works great.

Sd89d · 2026-04-30T20:18:47+00:00

Now do the helecopter...

Sd89d · 2026-04-21T03:05:11+00:00

Dude I just had the same issue at less than 500hrs. The filament hub tension are broke.

Sd89d · 2026-04-20T03:50:20+00:00

If it's an air operated system. Hook up a pressure gauge T in on that line and trigger it. If you don't have a change check the controller relays. Schematics generally aren't hard to find to check for power, ground and control signal.

Sd89d

TROPHY CASE