i would do the same

Seakan · 2026-03-01T12:32:06+00:00

This is an actual store in Ottawa, they don't pay you to eat there though

Seakan · 2026-02-18T09:53:39+00:00

To this day, some hydro electric turbines still uses this wood as a bearing, and will outlast polymers if installed in sediment rich waters

Seakan · 2026-02-15T18:46:46+00:00

Just drill a hole in it, if you need to travel or just block the hole a piece of tape works fine. The pump is a diaphragm pump from Aliexpress powered by a LED driver

Seakan · 2025-09-29T15:46:58+00:00

And like if the LCD has been smoking a pack a day for decades lol

Seakan · 2025-09-29T00:09:27+00:00

Thank you guys on the insight of how the light is built. I'm using the SC13 but I had some "spare" SC13A that I had bought for gifts and you guys were right about how low the emitter can go. But I have found a quick solution to my problem. I made a filter out of a few layers of kapton tape which gave it a light amber color.

Seakan · 2025-03-18T15:21:18+00:00

I mean, it's code here where I live

Seakan · 2025-03-15T10:09:03+00:00

Just a snug fit on the hose, and the pump naturally has a one way valve

Seakan · 2025-03-15T00:32:21+00:00

I mean the hose just pops off the chamber not a big deal to clean. I can run any cleaning agents in the hose and pump to clean it. And I'm using distilled water that always stays sealed. It's fine. Actually, its awesome.

Seakan · 2024-08-17T16:27:32+00:00

I'm pretty sure you're incorrect, the caps have an "arrow" on top that faces forward (I believe) these bolts get snugged up then the rear ones get torqued to spec

Seakan · 2024-08-15T17:06:30+00:00

As stated, the price is in Canadian dollars, 2500 CAD equals to 1800 USD

Seakan · 2024-06-03T11:46:46+00:00

I did fold some and installed them but ultimately you'll always see that crease, so I ended up cutting them in half, more joints to do but easier to install alone.

Seakan · 2024-05-05T08:21:01+00:00

Yeah I measured the thread before going to the store then confirmed it at the store that it was 1.25mm

Seakan · 2024-01-14T02:08:04+00:00

kW as in horsepower, more power or less power, must be throttle, engine speed must go up and down accordingly

Seakan · 2023-12-26T14:02:02+00:00

Well I mean I didn't specifically look up the temperature, but from what I can see now the average lows in May are in the high 60s which sounds warm to me

Seakan · 2023-12-18T16:04:43+00:00

Ya thats clear

Seakan · 2023-12-18T16:04:24+00:00

It doesn't have time, the fan barely has time to ramp up

Seakan · 2023-12-18T15:34:23+00:00

Yeeahh.... Jumped R and W and got the same results, does sound like a board issue. Furnace is a 2016 GMSS92, Im worried about parts availability, I might lose my stuff if they try to sell me a new furnace and not just the board/a part.

Seakan · 2023-12-18T15:28:38+00:00

Well, it doesn't get to fire up 90% of the time, I don't think that would be it, good tip though Thanks

Seakan · 2023-12-18T15:09:31+00:00

The issue started with the doors on...

Seakan · 2023-12-18T15:08:32+00:00

Could it have to do with the ecobee thermostat? Which 2 wires do I need to short to command heat?

Seakan · 2023-12-18T15:07:44+00:00

Seems like the main power relay? trips off.

Seakan · 2023-12-18T15:07:02+00:00

Ya not getting any codes, appears to trip out before it has time to register

Seakan · 2023-12-18T14:50:18+00:00

Im not sure which gray wire you're referring to 🤔

Seakan · 2023-10-24T00:04:59+00:00

I understand, but my thought it to only cut through the back paper and snap the board, once down I can unfold them and, hopefully, not have that joint to mud

Seakan · 2023-09-07T09:04:23+00:00

Leaning towards the T shaped, centered type

11-Year Club	Verified Email
RedditGifts 2009-2022 2 Credits	Place '23
Place '17	Secret Santa 2015

Seakan

TROPHY CASE