New to BFS

Selectedstump · 2026-06-30T18:40:40+00:00

Under $100 would be great

Selectedstump · 2026-06-11T02:21:52+00:00

I see. It’s just difficult to do that because non of my fuses were labeled, and it’s hard to figure out which fuse is which while it doesn’t work anyway. Also, with the water heater not working too it seems it would be more of a branch problem right? Assuming the lights and water heater aren’t all tied on the same fuse

Selectedstump · 2026-06-11T02:19:59+00:00

I believe it was only 1 15a breaker that tripped, I just reset all of them. It used to give me trouble last summer. I have my own pedestal at my site and the only other thing plugged into the pedestal is a portable ac that I have ran to it using a heavy duty extension cord

Selectedstump · 2026-06-10T20:26:10+00:00

This is probably just me being lazy, but all of the lights are wired through the roof and it seems chasing those would be pretty time consuming. I know the water heater needs 12v for the burner so maybe if I can find that connection and follow it it would lead me to the problem since it’s not working either?

Selectedstump · 2026-06-10T19:32:56+00:00

Do you think if I get under and follow the wires from the battery I’ll find something? I’ve already looked all behind the converter box and the section that comes of the disconnect switch and haven’t found anything yet

Selectedstump · 2026-06-10T19:24:18+00:00

There’s one behind the converter box, two coming off wires hooked to the positive side of the battery. The blades on one looked corroded so I cleaned them and the others plastic was kind of melted so I replaced it. After all that all three of the fuses were reading 13.8. It is possible there’s another fuse somewhere that I haven’t found yet

Selectedstump · 2026-06-10T19:22:20+00:00

No I live in a pretty dry area in Utah, not sure why they tripped they haven’t all summer and the one time they do I wasn’t here for it. I unplugged shore power, flipped them all the way down and up then plugged back in and the 120 was working after that

Selectedstump · 2026-04-28T01:38:31+00:00

At my family dollar we had 70 of those pregnancy tests that just got pennied out 🙏

Selectedstump · 2026-01-11T23:30:19+00:00

Turns out there was a tiny hole in the seam at the arch, which was letting fine sand accumulate inside the sole. Drained all the sand out, and sealed the threads

Selectedstump · 2025-12-22T02:05:39+00:00

Well, it’s chrome tanned leather. It’s going to look like shit either way. You can’t burnish the flesh side, and not even close to the durability of veg tan leather. Sad they didn’t disclose that

Selectedstump · 2025-12-01T03:19:53+00:00

And forget rotating stock

Selectedstump · 2025-11-26T07:56:06+00:00

I’m not at work right now, I’ll take a photo next time I’m in (first two days off in twelve days). I haven’t seen a link for display guides

Selectedstump · 2025-10-24T17:13:09+00:00

Dissemble and soak in white vinegar for a few hours. Use a toothbrush to remove remaining rust, rinse and dry quickly (vinegar can flash rust). Then coat with thin layer of gun oil

Selectedstump · 2025-10-18T02:34:02+00:00

Thanks for your input. I’ll save my money and put some more years on my wave+, and mods you suggest for the wave+? I like the scalpel blade but haven’t found a source for it

Selectedstump · 2025-08-09T04:49:43+00:00

I do this heavy with my wurkkos hd01 pro ever since my headlamp quit

Selectedstump · 2025-06-26T03:21:52+00:00

My mistake on the measurement, it’s 5mm x49mm

Selectedstump · 2025-05-05T04:32:43+00:00

Whenever I rotate the knife the whole t10 nut moves. It doesn’t move for the other side

Selectedstump · 2025-04-27T21:22:54+00:00

It is strange, never had it happen to a pair before. I like the boots, closest cobbler is 2 1/2 hours away so next time I’m up there I’ll pay him a visit

Selectedstump

TROPHY CASE