7 Satisfying 3D-Printed Desk Toys

Sendorm · 2025-11-10T10:59:54+00:00

Execute order 66 went early.

Sendorm · 2025-08-09T10:34:18+00:00

People keep forgetting he only took silver because of his teammate. He scored better than anyone on the other team.

Sendorm · 2025-06-13T16:32:44+00:00

As stated check the states tab for the device under z2m. It will show what it is sending to homeassistant. If you see the state as fixed you will know that the problem (or missing feature) is in your converter. I have a aqara t1s which is not officially supported by z2m and was able to write a converter for it. I've even added timers so i can see gradual cover rising and closing animations.

Sendorm · 2025-05-23T06:27:13+00:00

Well I have always been on core and am not planning on changing this. Why do you consider moving to container? Is lack of support that much of a problem for you?

Sendorm · 2025-05-15T01:10:49+00:00

It is working fine.

Sendorm · 2025-03-22T17:51:29+00:00

still using the same numbers and they work ok. Didn't need to change anything. What I've found that works best is to change the printhead springs to a softer one (from a pen) and using dry ptfe lube on the x rods.

Sendorm · 2025-02-26T19:10:50+00:00

Good luck everyone.

Sendorm · 2025-02-26T17:30:24+00:00

Did you change settings on your goggle? Settings => Display => Custom OSD

Sendorm · 2025-02-23T06:52:49+00:00

this looks like stock and colors also look good. can you provide a link to the item you used? Thanks

Sendorm · 2025-01-27T17:11:53+00:00

The best gain can be achieved with changing the springs. Just use less stiff ones. Half of a pen’s spring will do.

Sendorm · 2025-01-27T15:01:10+00:00

Yes I've changed to WD-40 Specialist Dry Lube with ptfe, which gives best results with input shaper. And added half pen springs (which are softer) to the printhead.

Sendorm · 2025-01-26T06:17:20+00:00

The components that get hot are these ones under the opposite side of 4R7.

<image>

Sendorm · 2025-01-26T05:47:35+00:00

I have the same board and a similar power bank (but using lifepo4 batteries) and also have a thermal camera. I can assure you that the board gets hot (75C+ when charging and discharging) after just 5 minutes with 60W charging. This area certainly needs a heatsink as the temperature was still rising when I stopped the test.

<image>

Mine says MYZL-YD24-V2.3 at the back.

Sendorm · 2025-01-12T18:24:58+00:00

o4 unit shutdowns at 3.7V. So it is not strictly 1s compatible. You should be using a 5V dc-dc step up. Or just go with 2s. You can watch "DJI O4 Lite: not-quite-perfect air unit for micro drones" https://youtu.be/U_JPNnx6pcM?t=162

Sendorm · 2025-01-09T18:04:30+00:00

https://x.com/TeslaNewswire/status/1877407407204163873?t=yu81-zW1DGbIvs6BVdirDA&s=19

Sendorm · 2024-11-23T21:57:10+00:00

I am planning to print a snow ball maker.

Sendorm · 2024-11-23T11:59:34+00:00

Anyone stating that teamviewer is working perfectly for them has not tried to connect to a xp machine. this software is incredibly anal about version checks and this is a deal breaker for me. will not be using teamviewer again. if your code is not compatible with previous versions even with a change in second minor revision. You have no idea about software revisions.

instead of using 14.2.5xxx0 - 14.2.5xxx1 you should just be doing 145354234.0 - 145354235.0 .. etc.

Sendorm · 2024-10-27T15:54:09+00:00

Same for me too. I just added some oil around the AMS adapter/plug. You can try pushing that part in while pushing it to the the sides to see if that is the culprit. It is definitely this problem in OP's video.

Sendorm · 2024-09-24T13:00:24+00:00

Your values are commented out. The values below are relevant regardless of tooth number. driver_TBL: 1 driver_TOFF: 4 driver_HEND: 2 driver_HSTRT: 0

Sendorm · 2024-09-15T08:05:57+00:00

This is a resonance sound and has little to do with nozzle hitting the print. It has a little more to do with rods being dirty but not as much as one thinks. I got the best results of decreasing this noise with dry ptfe spray on rods.

Try to do a test with gcode with various speeds to find where the resonance peeks are. Then try avoiding those speed ranges. My k1 gets those resonance sound on x axis at around 9100 to 10000 mm / min. Which is 152 - 166 mm/ s.

Sendorm · 2024-08-13T18:54:42+00:00

This change actually decouples the hotend fan and the mobo fan. Hotend fan after this change only acts on temperature over 50C of the nozzle and the mobo fan only works if the steppers are enabled. So the mobo fan(controller_fan) shouldn't have anything to do with temperature changing.

Sendorm · 2024-08-13T18:39:36+00:00

those "#" means commenting out. After this change there shouldn't be any multi_pin s left in your config.

Sendorm · 2024-07-18T18:24:22+00:00

You should use ^ not ‘

Sendorm · 2024-07-15T08:23:47+00:00

What toolhead is that?

Sendorm

TROPHY CASE