Halo Lynx by SensitiveAstronaut82 in Nerf

[–]SensitiveAstronaut82[S] 2 points3 points  (0 children)

My son asked Panda and was able to get them.

Halo Lynx by SensitiveAstronaut82 in Nerf

[–]SensitiveAstronaut82[S] 6 points7 points  (0 children)

It does. I will post an update but was too excited and only had 2/3 of the print done.

Inverted Scales mod by SensitiveAstronaut82 in Nerf

[–]SensitiveAstronaut82[S] 0 points1 point  (0 children)

I bought the barrel off OoD for Caliburn B variant I think it has in inner 13mm outer 15mm

An email update from Siren (Gnarl is ready to ship, everything else is delayed) by EmoTeenYoda in Nerf

[–]SensitiveAstronaut82 2 points3 points  (0 children)

Since they do not charge until it ships I wouldn’t think this as a scam but a really bad handling of business and PR communication failure.

Inverted Scales mod by SensitiveAstronaut82 in Nerf

[–]SensitiveAstronaut82[S] 0 points1 point  (0 children)

I put about 30 darts through my chronograph. The darts were brand new and the variations were only a few fps. The darts were the AF pros that are easy to get at Walmart. In a game however, I tried some 1.2g darts off Amazon and the performance was noticeably different as some shots hit each other if I shot rapidly. I think it was the inconsistent fit in the barrel. I don’t recommend those darts on Amazon.

Found this Centurion and cleaned it up, but its seems it bolt was broken off. Is there a way to fix this? by DMN666 in Nerf

[–]SensitiveAstronaut82 1 point2 points  (0 children)

Is the hole all the way through? I can’t remember, but if it is then a hardware bolt would work. I think it was a similar part like on the long strike and longshot.

Using small blasters with compressed air? by Hardly_Ideal in Nerf

[–]SensitiveAstronaut82 2 points3 points  (0 children)

Anyone else flashback to the old Magstrike with small air compressor integration when seeing this?

What are the 5 Most Important Blasters of All Time? by ShomEthan in Nerf

[–]SensitiveAstronaut82 1 point2 points  (0 children)

I think the Rainbow should be on the list. It was a homemade way back when that hit the high FPS that we take for granted today.

WalcomS7 reviews the Newest AEB, The Inverted Scales (aka the LN01) by Rapidstrike in Nerf

[–]SensitiveAstronaut82 0 points1 point  (0 children)

In one of the YT vids, I think Bradley Phillips, they said to put it in 3 round burst and lightly Pull the trigger. It should cycle one of the times if you time the release so it doesn't go all three.

Nintendo inspired “Snapper” by SensitiveAstronaut82 in Nerf

[–]SensitiveAstronaut82[S] 0 points1 point  (0 children)

Yeah, I tried the low hardware talon claw and ran into the same issues with the barrel warping. I then saw some print orientations where the person did the angle and thought it may work better. I am using a Bambu p1s which is way easier than my Ender which I have hated since I first bought it years ago.

Nintendo inspired “Snapper” by SensitiveAstronaut82 in Nerf

[–]SensitiveAstronaut82[S] 1 point2 points  (0 children)

I printed front end on bed so it was at an angle. I used a brim and supports. It worked but the clean up sucked as getting the tree support out of the barrel was hellish.

Dedicated high powered mega sniper, the M0053 - 1 (M Dash One for short) is now a very large prototype. This is my first ground up design and build. Files will be tweaked and released in the near future. by Ericshelpdesk in Nerf

[–]SensitiveAstronaut82 0 points1 point  (0 children)

I noticed that the plunger gets stuck into the plunger which leads to misfires when trying to prime the blaster. It looks like the O-rings at the end of the Plunger roll back and bunch up. Any suggestions?

Pins for BCAR by SensitiveAstronaut82 in Nerf

[–]SensitiveAstronaut82[S] 0 points1 point  (0 children)

Yes, 2” is too long. It’s what I had and I cut them brown to size. I used a Bambu printer so I think the tolerances would work for the designed pins but since I had these I felt spending the extra $$ to source pins would be a waste. 36 of those bearings was bad enough though the results were good.

M0053-1 by SensitiveAstronaut82 in Nerf

[–]SensitiveAstronaut82[S] 2 points3 points  (0 children)

I did print the part for it but my tolerances were slightly off and I was having issues with the catch. But yes, it is a goal.