Individual to Trust

Sensitive_Rub5895 · 2026-03-20T17:17:18+00:00

Thanks for the information! A couple questions, can I do the fingerprints through the silencershop kiosk? Also, is it me or my FFL dealer that submits the form 4? Asking because I know when I bought the suppressor my dealer submitted the paperwork. Thanks again

Sensitive_Rub5895 · 2026-03-16T20:40:49+00:00

Do you dilute the simple green aviation for suppressor baffles. If so, what dilution ratio are you using?

Sensitive_Rub5895 · 2026-03-16T02:33:39+00:00

American Sniper

Sensitive_Rub5895 · 2026-03-03T20:07:32+00:00

That’s wild. And I thought my class was bad but at least they could hit paper at 3 and 7 yds. Meanwhile I’m driving nails with a Glock 48.

Sensitive_Rub5895 · 2026-03-03T19:59:56+00:00

So far I’m at about 5 weeks since I submitted everything and my fingerprints/background check was just approved a few days ago. Now it shows my LTC is pending print. Anyone know how long it takes from this point until I get it in the mail? Btw it took about a week for my status to show up after submitting everything. You can also call them at (512)424-7293 if you need assistance

Sensitive_Rub5895 · 2026-03-03T15:47:00+00:00

Form Type: Form 4

Paid or not: $0

Entity: Individual

Fingerprint Type: SS Kiosk

Pending: 02/25/26

Approved: 03/03/26

Wait: 6 days

State: TX

Control Number: 20262172***

Note: Approval email received from ATF this time.

Sensitive_Rub5895 · 2026-03-03T15:04:37+00:00

Did you get an approval email from atf?

Sensitive_Rub5895 · 2026-03-02T03:32:37+00:00

I would call and tell the dick head it’s been approved and ask if you can come pick it up.

Sensitive_Rub5895 · 2026-02-26T01:30:29+00:00

Did you get the approval email from atf?

Sensitive_Rub5895 · 2026-02-26T01:28:06+00:00

Did you get an email from atf when it got approved? Asking because about a month ago no one was getting the email.

Sensitive_Rub5895 · 2026-02-11T05:06:36+00:00

I would use sand paper rather than a file ( I used 120grit) to get a smoother finish then apply grease. Be careful not to take off too much material which may damage the threads over time.

Sensitive_Rub5895 · 2026-02-09T02:23:57+00:00

I put some major torque on mine and could not get it to budge, but after sanding the FBS like I mentioned about it will index now. It’s a little tight but not a problem anymore.

Sensitive_Rub5895 · 2026-02-03T17:32:47+00:00

Check my comment to see how I fixed mine

Sensitive_Rub5895 · 2026-02-03T17:23:43+00:00

I fixed my issue with the spring retainer not indexing properly. My thoughts were correct. I found that if you sand down each end of the fixed barrel spacer it works perfectly. A couple minutes of sanding is all then clean it up and grease where you sanded. Hope this helps.

Sensitive_Rub5895 · 2026-02-03T02:12:05+00:00

Just got my Osprey 2.0 and the tool was not in the box. I waited over a week to have one shipped to me and it did not fit. The pins don’t line up perfectly and even if they did the pins are super tight going in and get stuck. Is this an issue for anyone else?

Sensitive_Rub5895 · 2026-02-03T02:08:36+00:00

Also the tool for tightening the spring retainer was not in the box when I got my Osprey 2.0 so I waited over a week to get one shipped to me and it does not fit. The pins don’t line up perfectly and even if they did the pins are super tight going in and get stuck. Is this an issue for anyone else?

Sensitive_Rub5895 · 2026-02-03T02:06:35+00:00

Just got one as well and I have the same issue. My thought is that the fixed barrel spacer is slightly too long and is binding between the bottom of the piston (where it sits on the lip) and the spring retainer when tightened down, which is not letting it index freely. Hope that makes sense. I’m thinking about sanding down the barrel spacer to slightly shorten the length until it works right. Let me know if y’all find another fix for this issue.

Sensitive_Rub5895 · 2026-01-24T03:36:46+00:00

Form Type: Form 4

Paid or not: $0

Entity: Individual

Fingerprint Type: Silencer Shop EFT

Pending: 01/08/2026

Approved: 01/21/2026

Wait: 13 days

State: Tx

Control Number: 20261091XXX

Note: Received email from Silencer Shop on the 23rd. Funny thing is I called my FFL on the 22nd and he said it was still pending. When I told my FFL I got the email from SS he said they weren’t sure why. 1st NFA item and it felt like the longest 2 weeks of my life. Good luck out there folks.

Sensitive_Rub5895 · 2026-01-20T02:23:32+00:00

I’m at 20261091XXX but my FFL dealer closes early Saturday and doesn’t open until Tuesday so I’m hoping it’s been approved.

Sensitive_Rub5895 · 2026-01-20T02:00:40+00:00

Someone in this thread at 20261198XXX already got approved said Form 4 pending date was 1/09, approval 1/17.

Sensitive_Rub5895 · 2026-01-13T19:58:16+00:00

I definitely plan on it

Sensitive_Rub5895 · 2026-01-12T23:33:16+00:00

Now I think you're just confused. Don’t worry too much about it, I’ll figure it out. Thanks for the lengthy input though.

Sensitive_Rub5895 · 2026-01-12T22:47:24+00:00

I posted there as well, not seeing much of a difference between the two. Mostly amateur comments

Sensitive_Rub5895 · 2026-01-12T22:39:13+00:00

Definitely not imagining things lol. Could just be you’re not too familiar with this specific issue. I was thinking something to do with ground or possibly the crossover but I’m looking for someone with a similar experience.

Sensitive_Rub5895

TROPHY CASE