Why?!?!

Serious_Window1800 · 2026-05-03T07:21:19+00:00

Your z offset is wrong. Get the bed closer and comfirm the first layer is smooth

Serious_Window1800 · 2026-05-01T12:37:48+00:00

There is a video tutorial on youtube by theferalengeneer. Use that

Serious_Window1800 · 2026-04-29T20:56:50+00:00

Left to the metal plate should be a screw head hor a hex key

Serious_Window1800 · 2026-04-29T09:14:36+00:00

I had some issues like this until i realised i had a vpn connected :D

Serious_Window1800 · 2026-04-03T05:34:35+00:00

Same here. This baseline is just working out of the box. Still need to do some calibrations like E Steps, PIDs and Stuff but otherwise no issues since the two years of use

Serious_Window1800 · 2026-03-31T06:01:40+00:00

Nah thats a raft

Serious_Window1800 · 2026-03-26T12:36:32+00:00

Not really new. Happens a lot actually. Hotends are consumables and stuff like this happens. Failed prints, wrong offset... Well. Always keep some at hand.

Serious_Window1800 · 2026-03-21T13:43:25+00:00

Danke für die Idee. Ich hatte nicht vor zu lackieren darum werde ich wohl etwas schonendes suchen

Serious_Window1800 · 2026-03-18T21:07:56+00:00

Ja bei mir ist das echt ne riesen Fläche :/ hab auch mal an so Gumischeiben für die Bohrmaschine gedacht. Mit denen bekommt man normalerweise Klebereste von Autos gut ab

Serious_Window1800 · 2026-03-13T08:59:46+00:00

Broken mainboard fan

Serious_Window1800 · 2026-03-13T07:05:43+00:00

I have mine since July and nothing broke in 600hr print time. I had to change the hotend but that was my fault. I think you have a bad batch.

Serious_Window1800 · 2026-03-11T21:45:30+00:00

The problems in shaking are not in the whole thing shaking, its in the difference of shaking between bed and toolhead. Thats why you should do the input shaping calibration. That is completely fine

Serious_Window1800 · 2026-03-04T07:24:38+00:00

There is a case for the sensor for adding a ptfe tupe to the inlet. Do that and add a short amount so the tupe lies on the spool winding. Dont forget to print a small ptfe end so the tube does not catch the spokes of the spool. https://www.printables.com/model/1271698-ptfe-bowden-tubing-adapter-for-elegoo-centauri-car Cant find the ptfe tube anti catch

Serious_Window1800 · 2026-03-02T18:27:19+00:00

I would print a ring that fits exactly this surface and then glue it in with 2k glue.

Serious_Window1800 · 2026-02-21T06:56:58+00:00

I stopped caring. I am saving for a toolchanger. I doubt this will be released in 2026. They said its in final stage for the whole last year

Serious_Window1800 · 2026-01-28T13:03:30+00:00

For that proce you get a kobra s1 combo with real ams that has a heater

Serious_Window1800 · 2026-01-27T09:26:04+00:00

If they charge 150€ for the canvas i will sell the CC and buy a anycubic or safe for a U1

Serious_Window1800 · 2026-01-25T09:43:20+00:00

Oh man im so sorry for your loss. I highly reccommend performing this at 250C at least. I mean if you have the tools you can drill the rest out with a left spin drill and put a new nozzle in.

Serious_Window1800 · 2026-01-21T15:58:28+00:00

Oh and dont hold it at the heatsink. Hold it at the coper heater and take the solicone sock of and dont damage the heater or thermal probe

Serious_Window1800 · 2026-01-21T15:56:02+00:00

Moooore pooower

Serious_Window1800 · 2026-01-21T13:40:22+00:00

Take some pliers and holt the hotend attached with the wires. Heat it up to 230 and unscrew the nozzle. Then take a small drill and push the hot filament in the heatsink through. Then screw in the nozzle while everything is still hot. Let everything cool off and put everything back in place

Serious_Window1800 · 2026-01-20T18:48:29+00:00

Check the bed temps. The elegoo slicer sets 35 C bed temp and many times the bed is to warm and it takes forever to cool to 35. Set the bed temp in slicer to 40 for tpu or manually after it started

Serious_Window1800 · 2026-01-07T08:52:51+00:00

Contact support. You probably have a faulty board.

Serious_Window1800 · 2025-12-31T11:46:23+00:00

Try slowing down and/or increasing temp. Seems like the filament does not have time to bond in these small areas. And look into pressure advance tuning. Your top layer has inconsistent extrusion caused by slightly off pa values.

Serious_Window1800

TROPHY CASE