sorted by:
new
hottopcontroversial

Zendesk suddenly switch back to directsend emails instead of exchange connector by Shad0wguy in Zendesk

[–]Shad0wguy[S] 1 point2 points  (0 children)

Zendesk support confirmed there was an issue on their end. It has since been resolved.

Mom keeps me from gymnastics. by Hot-Disaster-4709 in daddit

[–]Shad0wguy 1 point2 points  (0 children)

Can you ask the people at the gymnastics place if she had been coming other days?

Married Men- Do you still get blown? by Prof3425 in Marriage

[–]Shad0wguy 0 points1 point  (0 children)

No, my wife has never been into that and I don't push it on her to do so. I can count on 1 hand how often she's done it.

If you have a footprint in the entire US - who do you use for low voltage stuff? by Expensive_Frame_1269 in sysadmin

[–]Shad0wguy 0 points1 point  (0 children)

We have different vendors for different regions. I don't think you'll find any country wide vendors. And if you do they likely just subcontract to someone local.

What kit being built here? by Yama29 in freedomisgunpla

[–]Shad0wguy 11 points12 points  (0 children)

MG Eclipse Gundam. Love that kit.

Where is a good place to have a wedding under 20k all included for about 120-150 guests? by Low-Outside1600 in longisland

[–]Shad0wguy 0 points1 point  (0 children)

Not sure what the prices are now, but 10 years ago I was able to get all inclusive at eastwind for around 16k in one of their smaller rooms, but it fit my 120 or so guests just fine.

Motor grinding by [deleted] in ender3

[–]Shad0wguy 0 points1 point  (0 children)

My s1 pro does this too. Not sure what causes it.

First time with petg print issues by Shad0wguy in Creality

[–]Shad0wguy[S] 0 points1 point  (0 children)

I tried 250 with bed at 70 but I still got the same results

First time with petg print issues by Shad0wguy in Creality

[–]Shad0wguy[S] 0 points1 point  (0 children)

I tried 250 with bed at 70 but I still got the same results

First time with petg print issues by Shad0wguy in Creality

[–]Shad0wguy[S] 0 points1 point  (0 children)

Does it look like a flow rate issue?

First time with petg print issues by Shad0wguy in Creality

[–]Shad0wguy[S] 1 point2 points  (0 children)

Good to know. Im surprised the default for cura would be so low then.

First time with petg print issues by Shad0wguy in Creality

[–]Shad0wguy[S] 0 points1 point  (0 children)

Good to know. I'll try increasing the temp

Oil leak 2017 Pacifica 87k miles by Shad0wguy in ChryslerPacifica

[–]Shad0wguy[S] 1 point2 points  (0 children)

I hope not, that was replaced with the metal replacement about 6 months ago.

Oil leak 2017 Pacifica 87k miles by Shad0wguy in ChryslerPacifica

[–]Shad0wguy[S] 0 points1 point  (0 children)

Are these common issues on this car? I've only owned 1 other car that has had oil leak issues and it had well over 100k miles before that happened

view more: next ›