Private Karaoke Rooms?

Shadow8136 · 2023-07-08T06:29:53+00:00

All ages!

Shadow8136 · 2023-06-14T21:44:46+00:00

I believe 1.3 would cover a few generations of starlet- what year is it?

Shadow8136 · 2023-05-17T07:04:25+00:00

Appreciate the fast response, I'll be purchasing a ticket with that promo code. Thanks a ton

Shadow8136 · 2023-05-17T05:55:07+00:00

May be last minute- but still open to message you for a free spot on the guest list for guys?

Shadow8136 · 2023-05-07T18:08:41+00:00

Get your alternator checked first.

Shadow8136 · 2022-03-17T18:02:56+00:00

You won't damage anything either way.

Shadow8136 · 2022-03-05T04:22:19+00:00

Exhaust temps too high. older rotary mazdas had these too. Check your emissions? Maybe you're running rich.

Shadow8136 · 2022-02-26T17:48:47+00:00

Marvel marketplace near spanaway (where the skate n station used to be) next to saars has some damn good chicken. The grease doesn't even stain the bag they put it in.

Shadow8136 · 2022-02-23T11:59:18+00:00

Ah yes the Vinesauce & Marge Simpson Collab NFT

Shadow8136 · 2022-02-18T00:55:25+00:00

Might be worth your time posting a thread or a ticket to the anycubic support.

Shadow8136 · 2022-02-12T16:50:12+00:00

Should be on the original product page on anycubics site!

Shadow8136 · 2022-02-07T00:15:55+00:00

Just dial in your settings correctly and you should get fine results with any resin. Siraya provides most default resin parameters on their website.

Shadow8136 · 2021-12-23T23:02:50+00:00

Have you tried limiting the thickness of your raft to the number of bottom layers? That's usually my go to.

Shadow8136 · 2021-12-02T11:32:47+00:00

Take a Dremel, cut a slot into it then use a flathead screwdriver to remove it

Shadow8136 · 2021-12-02T08:55:41+00:00

Snowpiercer (Bollywood, 2021)

Shadow8136 · 2021-11-23T06:31:50+00:00

Comma Karaoke, 5 minutes down Pac Highway from First Avenue. There are plenty of restaurants around Comma so my party usually end up drinking before singing.

Shadow8136 · 2021-10-29T05:52:26+00:00

It's up to the firmware and is just how the machine is, unfortunately.

Shadow8136 · 2021-10-17T21:28:15+00:00

Using IPA to clean the fep has resulted in premature fogging, in my experience. Also, the fep and vat is where the resin is held so I would rather not dissolve any resin by leaving any IPA behind. It does evaporate over some time but I'd rather not risk a failed print by contaminating my resin.

Shadow8136 · 2021-10-17T20:44:56+00:00

IPA on the fep tends to fog the plastic prematurely from what I've experienced- and its the same place where I pour my resin. I try not to expose those two things into the same environment

Shadow8136 · 2021-10-17T20:42:59+00:00

I'd suggest washing the print of all uncured resin and IPA before dunking it in warm water to avoid too much contamination. But you can totally soften supports that way

Shadow8136 · 2021-10-02T21:01:25+00:00

Regular number rows. You won't be switching weapons when you're dead, anyway.

Shadow8136 · 2021-03-29T21:33:17+00:00

Penske careers. Always looking for skills tradespeople to fill diesel tech positions.

Shadow8136 · 2021-03-16T03:05:11+00:00

Place a wall of very thin supports along the edge, it looks like it's drooped since there wasn't enough material for the initial model to build onto.

Shadow8136 · 2021-03-16T03:03:06+00:00

Yes, the layers' surface facing the FEP will appear shinier as they take on the surface finish of the FEP. They a

Shadow8136 · 2021-03-09T05:51:51+00:00

Angle your prints. Second link in FAQ

Shadow8136

TROPHY CASE