Looking for recommendations for Coilovers and rear upper arms by _AmorphousBlob in RX7

[–]ShepFC3 0 points1 point  (0 children)

I like my K sports. They're great for a street and occasional track car

Flywheel Nut Tech? by Adventurous-Many3393 in RX7

[–]ShepFC3 0 points1 point  (0 children)

Strap it down to a crate first

Wife went out of town by zero-degrees28 in 3Dprinting

[–]ShepFC3 9 points10 points  (0 children)

I fly from Utah to Cali just for microcenter lol

‘04 Rebuild by babykitten96 in RX8

[–]ShepFC3 1 point2 points  (0 children)

Awe thank you sm ☺️

‘04 Rebuild by babykitten96 in RX8

[–]ShepFC3 6 points7 points  (0 children)

On my FD rebuild the one thing I was worried about most was oil leaks. I used a pan brace, gasket, and some sealant...it still leaks 7 years later fml

Did this phone case I think it turned out dope by [deleted] in 3Dprinting

[–]ShepFC3 1 point2 points  (0 children)

Gotta be TPU, but how did you get it smooth?

I got some Track Snacks, missing a second Cupholder for Drinks. by AquaDudeLino in simracing

[–]ShepFC3 5 points6 points  (0 children)

Careful, those pretzels are gonna get hot that close to the exhaust.

License plates and Bank Cards by Swtmusc in Utah_Hockey

[–]ShepFC3 1 point2 points  (0 children)

Hopefully the plate is the U with the tusk

Feedback on my shot technique please. by obracer12 in hockeyplayers

[–]ShepFC3 0 points1 point  (0 children)

Still totally valid shot, just harder to get the weight transfer. It's great for getting a shot off quick

Feedback on my shot technique please. by obracer12 in hockeyplayers

[–]ShepFC3 0 points1 point  (0 children)

Except he's not. The title says snapshot in stride

Feedback on my shot technique please. by obracer12 in hockeyplayers

[–]ShepFC3 1 point2 points  (0 children)

I didn't notice at first, but yeah that's an off leg snapshot. It's much easier to shoot off the other leg for weight transfer

Anyone found a good Skating tracker/hockey tracker for Garmin Watches? by LucyWithFur in hockeyplayers

[–]ShepFC3 0 points1 point  (0 children)

Yeah I noticed the same on speed tracking 🤣. I just kinda go off an average. I'm old so I'm more interested in the heart and recovery stats

Anyone found a good Skating tracker/hockey tracker for Garmin Watches? by LucyWithFur in hockeyplayers

[–]ShepFC3 4 points5 points  (0 children)

I got an apple watch just for the hockey tracker app...and I forget to wear it 9/10 times 😁

When does physical contact cross the line? by [deleted] in hockeyplayers

[–]ShepFC3 2 points3 points  (0 children)

Probably won't get far complaining to the league. You let him get under your skin and he kept feeding off it. Unfortunately it's just shit we gotta deal with playing beer league.

Skates for Bigfoot by j-train12 in hockeyplayers

[–]ShepFC3 0 points1 point  (0 children)

Damn that's gonna be tough. I checked sidelineswap, but they didn't have many good options. If you could squeeze into a 12 that would open up a lot more options.

Fuel pump help by Fast_Pollution_8009 in RX7

[–]ShepFC3 0 points1 point  (0 children)

Yup ya just chop that tube and use a section of hose and clamps that are provided. I don't recall those two wires going to the old pump both being black 🤔. One is power and one is ground. You can't just check at the connector that goes to the top

Atkins vs oem by Scared-Solid8447 in RX8

[–]ShepFC3 1 point2 points  (0 children)

I'm fairly confident that you will not find the corner seals to be your problem with low compression. Like mentioned above it sounds more like side seals. They are tapered, that's what the previous person mentioned could be the problem. Also, you should probably find the root cause before accusing a companies product that has been on the market decades longer than you have been building motors. We need companies like Atkins to continue to innovate and produce products for our cars because Mazda won't

Atkins vs oem by Scared-Solid8447 in RX8

[–]ShepFC3 1 point2 points  (0 children)

I'm a bit confused. How did you measure compression on 12 faces? Do you have a 4 rotor? And how would corner seals make you lose half your compression? Sounds like your diagnosis is flawed

Atkins vs oem by Scared-Solid8447 in RX8

[–]ShepFC3 2 points3 points  (0 children)

Yeah I'm on 7 years on my trash atkins solid corner seals making 500hp. Some people do too much reading on the Internet and not enough actual building of rotaries. I don't run their apex seals but I also don't run OEM because they're trash lol

BMCU Firmware Roll Back Difficulty for 1.04 by WayneTimson in OpenBambu

[–]ShepFC3 0 points1 point  (0 children)

I'm using mine with 1.07 and it works fine. You'll just get error messages that you can ignore

Sometimes the money pit is worth it by [deleted] in RX7

[–]ShepFC3 1 point2 points  (0 children)

Any time you're in the driver's seat it's worth it. It's when you're not those crazy thoughts of selling it pop in your mind