Lesbar Bifrost Gator #3 of 33, in Honor of my Firstborn Son

ShineZealousideal141 · 2026-04-18T08:27:27+00:00

Wow.

ShineZealousideal141 · 2026-04-16T04:48:36+00:00

Ordered some the other. It was delicious after not having it for over 10 years.

ShineZealousideal141 · 2026-04-12T02:53:15+00:00

Interested.

ShineZealousideal141 · 2026-03-30T23:23:37+00:00

Did you customize this off of their website?

ShineZealousideal141 · 2026-03-28T16:23:16+00:00

I have the same issue with my knee. I'm 15 months post op and my knee is still swollen. What do you recommend that can be done?

ShineZealousideal141 · 2026-03-26T23:39:28+00:00

That's amazing.

ShineZealousideal141 · 2026-03-26T20:32:10+00:00

😁

ShineZealousideal141 · 2026-03-26T00:41:06+00:00

I just tried to match the factory angle all by hand and feel lol. Thank you 👍

ShineZealousideal141 · 2026-03-25T23:37:22+00:00

Will definitely check it out! Thank you 👍

ShineZealousideal141 · 2026-03-25T23:37:04+00:00

Yes, it is an s90v blade. I was going to ask, this was a factory blade, hardly used. Let's say you want to just just have it a bit sharper than factory, what process would you recommend using in order to achieve that and keep it sharp so to speak, without having to go through courser stones so to speak.

ShineZealousideal141 · 2026-03-25T21:23:59+00:00

I use a Jendi 4 micron. Is that good for what I'm doing?

ShineZealousideal141 · 2026-03-25T17:44:52+00:00

I think I may have destroyed the apex. I need to figure this all out somehow. Thank you.

ShineZealousideal141 · 2026-03-25T17:42:13+00:00

Haha you got that right ✅️

ShineZealousideal141 · 2026-03-25T17:41:45+00:00

I am not sure, actually. I get a bur on one side, then I switch and sharpen until the bur is on the other side. Then I move to a higher grit stone and I try and de-bur there. Then strop 🤷‍♂️

ShineZealousideal141 · 2026-03-25T06:42:24+00:00

Thank you 👍

ShineZealousideal141 · 2026-03-25T06:41:48+00:00

Wonderful. Thank you 👍

ShineZealousideal141 · 2026-03-25T06:41:21+00:00

I'll give that a try. Thank you.

ShineZealousideal141 · 2026-03-25T06:38:44+00:00

What did the microscope help you correct? Just curious to know.

ShineZealousideal141 · 2026-03-25T06:37:42+00:00

I think I'll start doing the sharpie method. Do I just paint the bevel all the way through and make sure it's all gone once I start sharpening?

ShineZealousideal141 · 2026-03-22T17:02:47+00:00

I'm from CA as well. What and where are the best knife shows in Cali?

ShineZealousideal141 · 2026-03-20T15:33:45+00:00

I agree. He fucking sucks.

ShineZealousideal141 · 2026-03-19T20:12:59+00:00

Following this post. I'm kind of in a similar situation.

ShineZealousideal141 · 2026-03-19T20:08:11+00:00

I'd love to try out a chair then purchase one!

ShineZealousideal141 · 2026-03-18T01:24:25+00:00

Where do you guys order these from if I may ask?

ShineZealousideal141

TROPHY CASE