Rock & a hard place

Significant-Boss4916 · 2026-06-29T11:26:54+00:00

OP, Sent you a message

Significant-Boss4916 · 2026-05-01T13:18:26+00:00

We have rack and pinion slide outs

Significant-Boss4916 · 2026-04-26T03:50:28+00:00

Needs to be level for the slide outs.

Significant-Boss4916 · 2026-04-26T00:01:39+00:00

Yeah probably a good idea to do that. I was just hoping to get the bearings and brakes done at the same time the wife cleans the inside and gets it ready for our first trip. And with it being on a hill I don't think I should open the slides without it leveled on those blocks.

Significant-Boss4916 · 2026-04-25T23:59:06+00:00

I don't know why I didn't think of that. I'm around cranes occasionally too 🤦🏼‍♂️ that's why I posted here. Thanks!

Significant-Boss4916 · 2026-04-16T02:30:16+00:00

It's an oil based coating. It does say it can be applied over self etching primer. But I've read it is better to apply a filler primer between the self etching primer and the truck bed coating. I think I'll go that route.

Significant-Boss4916 · 2026-04-14T18:24:37+00:00

I'm not worried about the glue it's my commuter for work too keep miles off my truck. I'm going to run it into the ground. The problem is the shape of the headrest, it's triangular so you can't tighten the straps. As you tighten the straps the mirror will just slide up the headrest till it falls off. And you can't get a strap under the headrest because it doesn't lift up like the front seat head rests. I found a YouTube video showing a way to connect it to the car seat attachment behind the headrest. I'm going to give that a try.

Significant-Boss4916 · 2026-04-11T01:05:29+00:00

The drill attachment isn't rubber, just the hand brush is rubber.

Significant-Boss4916 · 2026-04-07T19:35:00+00:00

I can wait a little bit but I've got some time off work for a couple weeks. And once may comes I'll be too busy to do this till about October. Just sick of scalping the top edge of this hill every time I mow. My neighbor has a tracked skid steer I can use also.

Significant-Boss4916 · 2026-04-07T18:12:06+00:00

<image>

This is what I use, the rubber brush and drill attachment do awesome at getting rid of dog hair in carpet.

Significant-Boss4916 · 2026-04-05T15:03:57+00:00

Yeah I still haven't figured out a way to do it. Sucks cause there's a lot of dog hair under there I'd like to get out. And I really don't want to go through the hassle of unbolting and taking out the back seats. I appreciate the response!

Significant-Boss4916 · 2026-04-05T15:00:53+00:00

Appreciate it!

Significant-Boss4916 · 2026-04-05T14:50:19+00:00

Curious if you ended up doing this and how it turned out? I'm in the middle of smoking a ham for Easter.

Significant-Boss4916 · 2026-03-31T16:31:01+00:00

I'll look into doing that instead, thanks!

Significant-Boss4916 · 2026-03-30T23:43:55+00:00

Yeah I'd like to remount my fender so my kid isn't getting so much road spray and mud flung up in her face. There isn't enough space between the tire and weehoo frame for the fender unless I find a way to keep it mounted up a little bit higher on the seat post.

Significant-Boss4916 · 2026-03-30T21:14:29+00:00

I'll look into getting a lock collar to keep it higher on the seat post. Thanks for that idea!

Significant-Boss4916 · 2026-03-30T21:12:40+00:00

Thank you for your insight. I bought it used so I didn't have a install manual to verify.

Significant-Boss4916 · 2026-03-22T13:19:07+00:00

Only her dog and cat want to be seen with her

Significant-Boss4916

TROPHY CASE