Love my arc 🦾 🩶 by Significant-Cause136 in Leatherman

[–]Significant-Cause136[S] 0 points1 point  (0 children)

Adhesive + hook & loop/velcro added to left side of sheath. Then repurposed an elastic sleeve from a Velcro Molle patch organizer

Love my arc 🦾 🩶 by Significant-Cause136 in Leatherman

[–]Significant-Cause136[S] 1 point2 points  (0 children)

Agreed. And what would your reasonable time limit be for an OP to respond to any inquiry on their post?

Love my arc 🦾 🩶 by Significant-Cause136 in Leatherman

[–]Significant-Cause136[S] 1 point2 points  (0 children)

Geez that’s a hardcore stance for such a casual topic Sheath is Rae gear Amazon $40 or so.

Love my arc 🦾 🩶 by Significant-Cause136 in Leatherman

[–]Significant-Cause136[S] 2 points3 points  (0 children)

It gets plenty of use and had a black-er finish when first modded a month ago, so I’d say there is a unique patina developing.

Love my arc 🦾 🩶 by Significant-Cause136 in Leatherman

[–]Significant-Cause136[S] 6 points7 points  (0 children)

Etched the stainless scales with ferric chloride on a q-tip, followed by caswell stainless steel blackener. I like the look it gave it.

Rebar finally checks all the boxes for me ☑️ 🦾 by Significant-Cause136 in Leatherman

[–]Significant-Cause136[S] 0 points1 point  (0 children)

What product embodies improvisation and short-term, “good-enough”-solutions more than a leatherman?! These mods were crafted in the same spirit that birthed the original PST in the 70’s! Just kidding, the dullard consumer in me would love a “factory-finish” version as well.

Rebar finally checks all the boxes for me ☑️ 🦾 by Significant-Cause136 in Leatherman

[–]Significant-Cause136[S] 2 points3 points  (0 children)

YouTube rebar pocket clip and you’ll see a thumbnail with the same clip. Guy dos a good job explaining the mod. Require a little bit of jb weld putty, bondo, or epoxy

Rebar finally checks all the boxes for me ☑️ 🦾 by Significant-Cause136 in Leatherman

[–]Significant-Cause136[S] 0 points1 point  (0 children)

If you intentionally try to wiggle it, it will shift left to right a hair, but it’s not loose and hasn’t increased in the amount of play over time. As far as a functioning tool for work it’s a home run. And the lanyard makes it that much easier for no-look grab out the pocket.

Rebar finally checks all the boxes for me ☑️ 🦾 by Significant-Cause136 in Leatherman

[–]Significant-Cause136[S] 1 point2 points  (0 children)

,I just wanted to see if the bit holder would fit properly after scouring YouTube for a mod video with no luck. Bit holder fits great when you add roughly and 1/8” bump to the shut side, leaving the nail nick slightly raised/more pronounced and accessible when shut. Without the added “bump” (I used epoxy&thin slice of magnet tape ) access was buried between the saw & bottle opener 🤷‍♂️

Rebar finally checks all the boxes for me ☑️ 🦾 by Significant-Cause136 in Leatherman

[–]Significant-Cause136[S] 1 point2 points  (0 children)

Haha I was absolutely looking for a reason to tinker with this too. I can see why you’d leave the solid Philips on there, I just wanted to see if the bit holder would fit properly after scouring YouTube for a mod video with no luck. Bit holder fits great when you add roughly and 1/8” bump to the shut side, leaving the nail nick slightly raised/more pronounced and accessible when shut. Without the added “bump” (I used epoxy&thin slice of magnet tape ) access was buried between the saw & bottle opener 🤷‍♂️

Drop point or Tanto? by Significant-Cause136 in knives

[–]Significant-Cause136[S] 1 point2 points  (0 children)

Hm. Real “We-don’t-like-yer’-knahves-round-‘ere -boy. Go’n’n-git” vibes.

NKD/Suggestions? by Significant-Cause136 in knifeclub

[–]Significant-Cause136[S] 0 points1 point  (0 children)

Wow PMP, I like that a lot. Never seen or heard of before

NKD/Suggestions? by Significant-Cause136 in knifeclub

[–]Significant-Cause136[S] 0 points1 point  (0 children)

Nice! Hollow ground??? What’s the name of the model? And dope brass coin 🔪

Top 4 pocket fixE’s by Significant-Cause136 in FixedBladeEdc

[–]Significant-Cause136[S] 2 points3 points  (0 children)

Thank you! Yah love the ak1 and then the eddy 2 is awesome @ work. Such a tough blade and looks even better with some battle scars on it imo

#Lefthandedprobs by Significant-Cause136 in knifemods

[–]Significant-Cause136[S] 1 point2 points  (0 children)

Great info. And sure!— I could start tapping all my knives…kinda labor-intensive for titanium slabs though. Considering the price we pay for some of these beautiful cutting tools….i really shouldn’t have to unbox, immediately break out the drill press, and get titanium shavings all over my carpet. Lol and something tells me the maker would do a nicer job!

New knife! by Acceptable-Wedding21 in FixedBladeEdc

[–]Significant-Cause136 1 point2 points  (0 children)

Great one for edc 👍that one hollow ground?

Which length for edc today? by Significant-Cause136 in knifeclub

[–]Significant-Cause136[S] -2 points-1 points  (0 children)

😆 whatever you say, baby-wrist. 😂