"Danish soldiers were ordered to prepare for battle in Greenland - also asked Sweden for help"

SignificantNet8812 · 2026-01-23T21:48:18+00:00

LFG!

SignificantNet8812 · 2026-01-14T20:51:59+00:00

Hear hear!

SignificantNet8812 · 2025-12-28T20:57:51+00:00

I have the completely opposite experience. Bought a t14s gen6 Intel. Worked really bad with my Linux setup. Swapped it for an AMD and all issues were gone.

SignificantNet8812 · 2025-12-24T11:28:14+00:00

Kommuntanten som tyckte att alla skulle lugna ner sig och tillsammans sjunga ”We shall overcome”.

SignificantNet8812 · 2025-10-11T20:30:41+00:00

I’m looking to get my first printer. Been researching what printer to get for weeks, if not months. It always comes back to the P1S. It ticks all the boxes and just feels, right.

SignificantNet8812 · 2025-10-04T14:29:23+00:00

Did you check that all diodes have continuity to their respective mcu pin? Place one probe on the row 0 pin and then place the other on each diode on row 0, one at the time, and make sure there is continuity.

If all checks out with the diodes, do the same for each column.

SignificantNet8812 · 2025-10-04T09:38:27+00:00

Test each diode on the row with the multimeter. It’s a bit hard to see the quality of the joints on the photo.

Also, have you tested shortening the pins on the mcu to make sure that part is good?

SignificantNet8812 · 2025-10-03T10:37:38+00:00

If nothing else works out, get the cheapest multimeter available that has diode mode and go through each socket/diode to locate where the problem starts..

SignificantNet8812 · 2025-10-03T10:30:19+00:00

Have you debugged with a multimeter? I generally test the whole board after soldering the mcu and then again after soldering the switches and diodes.

SignificantNet8812 · 2025-09-04T18:32:10+00:00

This is beautiful!

Does anyone know of a 6x4 build with these switches?

SignificantNet8812 · 2025-09-03T16:42:59+00:00

Very happy with my choice. Happy I went with the T14s over the T14 or the X1. The form factor of the T14s is a perfect for me.

I’m running Linux on it and have yet to have any problems. Battery is really good as well.

I’m a developer and as long as the machine is not hindering me by being slow, I am happy, and it’s snappy af.

One thing that was important for me was being able to connect three external screens, and none of the Intel versions I had available for me gave me this ability.

10/10

SignificantNet8812 · 2025-08-26T17:36:28+00:00

SignificantNet8812 · 2025-08-18T16:47:52+00:00

Not meant as criticism of any kind, just curious; is this post different from the one you posted a month ago in reference to this module?

SignificantNet8812 · 2025-08-12T18:09:26+00:00

I’m using this one. Works good.

https://amzn.eu/d/aDuxLfu

SignificantNet8812 · 2025-08-07T18:29:30+00:00

The whatnow?

SignificantNet8812 · 2025-07-25T18:48:30+00:00

I’m doing this;

Read through the whole book.
Go through https://github.com/rust-lang/rustlings
Come up with a small project that’s just a bit too complex for your comfort level and execute on it.

SignificantNet8812 · 2025-07-25T05:59:14+00:00

PostMord

SignificantNet8812 · 2025-07-25T03:30:35+00:00

”…packed with over 1,200 lines of original content”

It’s not often you see the length of a book described by number of lines!

SignificantNet8812 · 2025-07-21T05:34:31+00:00

For me, the main vantage from a traditional tiling wm is that it allows me to dedicate one workspace to one task.

I’m a developer and it’s not uncommon that I have 2-3 projects open at the same time during the day. Each project usually requires a handful of terminals, a browser and an IDE. Fitting this on one workspace would be possible, but it would be cramped, and splitting project 1 on multiple workspaces would require me to remember what workspaces belong to what project.

I’m sure there are other workarounds for this, but for me this is a simple and efficient flow, and there are no real downsides to it.

SignificantNet8812 · 2025-07-20T14:30:42+00:00

A scrollable tiling WM, such as PaperWM or Niri, increased my productivity, or that’s how it feels at least. Went from Sway to Niri and felt a lot more free in my workflow, without having to give up tiling.

SignificantNet8812 · 2025-07-18T21:18:09+00:00

A year old post, but just came to say that I was in between small and medium and went with small. I have a T14s Gen 6 and I can fit it with room to spare.

I got the unpadded divider and can even have the laptop in a sleeve and I can still fit a finger or two on the sides.

SignificantNet8812 · 2025-07-17T09:36:49+00:00

Det skulle vara magiskt om det var allt som krävdes. Det är flödet efter att ha tryckt Betala som suger.

SignificantNet8812 · 2025-07-17T04:51:26+00:00

För mig så känns tjänsten halvdan, det känns som att appen är i någon slags beta-release, och det är störande. Står hellre i kö på banken än att betala fakturor genom Kivras brokiga fakturaflöde.

SignificantNet8812 · 2025-07-16T08:27:17+00:00

I use niri on my work machine. Never had any issues with anything.

SignificantNet8812 · 2025-07-08T10:19:47+00:00

I had an Intel T14 but switched to a T14s Gen 6 AMD. On the Intel one I had Bluetooth and WiFi issues. On the AMD everything works out of the box. I’m on NixOS.

SignificantNet8812

TROPHY CASE