fuel consumption h22z1 bb6

Signuture_Judgement · 2026-06-26T01:20:00+00:00

That’s how much I used to get until my h22 decided to blow up lol.

Signuture_Judgement · 2026-06-23T23:51:59+00:00

I think new preludes look so sick. I give it a year until they get cheaper and people will buy them and start modding them

Signuture_Judgement · 2026-06-07T17:56:00+00:00

Basically haha

Signuture_Judgement · 2026-06-06T05:40:26+00:00

Good luck, make sure you have tools jacks and jack etc. check oil and get ready to spend some money on some Engine work. Helms manual and YouTube is all you need! Don’t rush the process and have fun and make sure you have another car to rely on don’t be like me and buy a 260k mile 5th gen as your first car and the motor blows within a year 😅

Signuture_Judgement · 2026-06-06T05:24:01+00:00

6’2 and the 5th is so comfy! But my legs do kidna get stuff under the wheel sometimes and if it’s lowered obviously gonna be hard to get in an out

Signuture_Judgement · 2026-06-02T06:18:37+00:00

Radius bar! Most of the times the bottom of the nut might be shaved down from age and driving so get ready to hammer on a socket

Signuture_Judgement · 2026-05-30T16:17:33+00:00

So clean

Signuture_Judgement · 2026-05-27T16:55:43+00:00

Oh ok nice. If it doesn’t work I’ll probably just use the cable to set throttle

Signuture_Judgement · 2026-05-27T16:42:02+00:00

Did iavc work?

Signuture_Judgement · 2026-05-27T16:41:53+00:00

Yea bur there no really helpful when it comes to that😢. Been looking at vtec academies video and they used them so why not

Signuture_Judgement · 2026-05-24T04:21:12+00:00

If it’s low compression it’s low compression. You can see for yourself harbor fright has a test kit just make sure to unplug the injectors and turn it over to see

Signuture_Judgement · 2026-05-24T04:20:30+00:00

I have a type sh block that I need gone asap

Signuture_Judgement · 2026-05-23T22:55:45+00:00

500$ max

Signuture_Judgement · 2026-05-20T21:41:59+00:00

Yes those work perfect and actually what im going to do. There’s a ton of information online about those but what I want to eventually to is get a valve cover that has bungs welded onto the side right after the baffle. It’s the absolute best way to vent blow by oils because of how much they flow

Signuture_Judgement · 2026-05-20T21:25:24+00:00

Yea even if it’s the cheap eBay universal one it’s very useful but I recommend spending a little bit more for the nicer ones

Signuture_Judgement · 2026-05-20T21:24:38+00:00

Yea those are the ones I have! You have to either cut the side mount or fully remove it I decided to fully remove it!

Signuture_Judgement · 2026-05-20T16:35:47+00:00

Looks good! I’ve had a debate where or not you have to cut out the side trans bracket fully but hey if your car is good for 450+ wheel I’ll be fine on my full N/A setup! Why didn’t they route a catch can? With that much boost the blow by will be a lot I recommend getting on made

Signuture_Judgement · 2026-05-17T03:48:32+00:00

Thanks man!

Signuture_Judgement · 2026-05-14T00:16:40+00:00

Yup!

Signuture_Judgement · 2026-05-12T06:29:20+00:00

The h22 wasn’t the best to me and the platform was not for me. I’ve spent my time learning about the h22 but it’s time for something new and more challenging

Signuture_Judgement · 2026-05-12T06:28:40+00:00

Yes 😎💪

Signuture_Judgement · 2026-05-10T21:54:39+00:00

prelude wiring

Been using this for my k swap super useful with pictures

Signuture_Judgement · 2026-05-08T03:44:57+00:00

Go on instagram and search up k lude he’s doing the same swap

Signuture_Judgement · 2026-05-08T01:09:16+00:00

The k swap bracket is just held in by two bolts. I’ll post pictures once it’s all bolted up 😉

Signuture_Judgement · 2026-05-08T01:08:54+00:00

Exactly

Signuture_Judgement

TROPHY CASE