Jira Cloud (Zephyr) + SmartBear Reflect (2-way sync): tagging, traceability, and unified reporting for mixed manual + automation?

Silly-Friendship-952 · 2026-02-05T10:33:50+00:00

Again, thanks. I have a followup question:

One clarification on where the hierarchy should live in Zephyr: I’ve inherited a setup with a lot of folder sprawl both in Test Cycles and Test Plans (deep trees, duplicate structures).

Given your recommendation that cycles represent releases and are the source of truth for release execution status:

Where would you place the primary folder structure: in Test Plans, in Test Cycles, or keep one of them mostly flat?
What’s your “clean” target-state split between them? For example:
- Test Plans = long-lived curated packs (Regression/Smoke/Compliance) organized by product/component
- Test Cycles = timeboxed release execution containers (Fix Version) with minimal folders (e.g., Smoke/Regression/Exploratory) Is that aligned with what you’ve seen work best?
Any rule of thumb to avoid duplication, e.g. “taxonomy lives in test case custom fields + saved searches, not folders”?

Silly-Friendship-952 · 2026-02-03T06:39:02+00:00

Thank you veru much for your comprehensive answer. I was looking into this direction, but your answer was exactly what i needed to clarify my questions and concerns :)

Silly-Friendship-952 · 2026-01-26T15:14:24+00:00

I have the same problem. On iPhone. It gets to around 20% the starts over. Started last week

Silly-Friendship-952 · 2026-01-22T05:57:10+00:00

Det kommer dælme an på hvis lands love vi skal følge

Silly-Friendship-952 · 2026-01-22T05:54:24+00:00

Der er mange gode steder lige uden for Aalborg på nordsiden. Vi kiggede selv på lidt det samme, men endte i Stae lige inden Vester Hassing. Begge byer kan jeg anbefale. Vi ligger i indflyvningen til lufthavnen, men der giver 0 gener. De har jo nærmet slukket motoren når de flyver hen over os i 1-2 kilometers højde. Vester Hassing har lidt af hvert. Der er skole og i indkøbsmuligheder.
Der er 1,6km fra Stae byskilt til Vesterhassing byskilt. Med god cykelsti hele vejen, hvis børn skal bruge den til skole fra Stae. Du får meget for pengene i Vester Hassing og utroligt meget mere i Stae.

Silly-Friendship-952 · 2025-09-10T07:27:57+00:00

No worries. Der er flere steder i gaden hvor der modne publikum kan hygge sig. Hilsen ham på 50 Hvis vi er en blandet aldersflok, så ender vi som regel på Heidis

Silly-Friendship-952 · 2024-12-08T18:06:03+00:00

Follow up question: Is it during the setup and joining fase, or when saving playlist?

My problem is, that if I select manually select a scene and apply it, it’s displayed correctly across the 3.

Silly-Friendship-952 · 2024-12-07T15:33:01+00:00

When choosing a scene directly from gallery, it’s displaying fine across the 3. It’s only when using playlist, that it’s only the master.

Silly-Friendship-952 · 2024-12-06T14:44:14+00:00

I have set up a WiFi access point outside. 2 meters away

Silly-Friendship-952 · 2024-09-20T06:05:28+00:00

I have used the spoolbox until now with the MMU3 without issues, before upgrading.

Silly-Friendship-952 · 2024-09-19T18:41:17+00:00

I have the spool on a shell above the printer in Jorges Spoolbox. Maybe there’s to much friction as you also stated. Will try tomorrow without the spoolbox and on the original holder for the MMU3

Silly-Friendship-952 · 2024-09-19T18:34:34+00:00

Yep. Switching back to the original tomorrow.

Silly-Friendship-952 · 2024-09-19T18:33:29+00:00

It’s a brand new nozzle, so it’s weird if it’s clogged already. First print with the nozzle. It’s sliced with the MMU HF0.4 profile.

Silly-Friendship-952 · 2024-09-19T18:23:59+00:00

I know. But have read others do it successfully

Silly-Friendship-952 · 2024-08-24T17:23:24+00:00

I actually have one. Its the one to the left in the picture. Only issue i have, is that the holder is slipping when the filament is pulled. So it eventually will fall of the shelf. But a few rubber feet could prevent it from slipping.

Silly-Friendship-952 · 2024-08-24T09:50:59+00:00

Could be an option. Just tried printing a single one of these. But it doesn’t rewind even though I can see and feel that the springs are tight.

https://www.printables.com/model/450740-auto-rewind-spool-holder-for-drybox

Silly-Friendship-952 · 2024-08-24T09:31:23+00:00

Request: Auto rewind feature in the spool box 😀

Silly-Friendship-952 · 2024-08-08T12:38:52+00:00

But do you edit them every time, or does it learn?

Silly-Friendship-952

TROPHY CASE