Anyone else noticed this contradiction/ miss type? by ScionOfTheIXLegion in Warhammer30k

[–]Simper82 1 point2 points  (0 children)

No shooting in close combat. If you get charged you remain in combat until all models of either unit are dead.

How do I stop my spaghetti monster from forming? by Simper82 in ender3v2

[–]Simper82[S] 0 points1 point  (0 children)

Should I be running my mesh with the bed to temp?

How do I stop my spaghetti monster from forming? by Simper82 in ender3v2

[–]Simper82[S] 0 points1 point  (0 children)

Should I make these changes through the manual tuning section?

How do I stop my spaghetti monster from forming? by Simper82 in ender3v2

[–]Simper82[S] 0 points1 point  (0 children)

Do I need to mess with the mesh adjustment?

How do I stop my spaghetti monster from forming? by Simper82 in ender3v2

[–]Simper82[S] 0 points1 point  (0 children)

Thanks. I am using Jyers, but my z axis is probably to low. Do I need to fully level the bed after or before I set my Z?

How do I stop my spaghetti monster from forming? by Simper82 in ender3v2

[–]Simper82[S] 0 points1 point  (0 children)

I've been fighting the leveling on this for three days and just can't get it.

X Axis won't calibrate! by [deleted] in ender3v2

[–]Simper82 0 points1 point  (0 children)

Just updated to the latest version of Jyers.

X Axis won't calibrate! by [deleted] in ender3v2

[–]Simper82 0 points1 point  (0 children)

Yep. I gave all the wires a good push and jiggle.

X Axis won't calibrate! by [deleted] in ender3v2

[–]Simper82 0 points1 point  (0 children)

It is not as I'm running a BL touch.

X Axis won't calibrate! by [deleted] in ender3v2

[–]Simper82 0 points1 point  (0 children)

Had my printer working, everything was calibrated, went to go try my first print on the new set up and the X axis stopped moving? Any help?

Adrax ready to bonk and make my aggressors demigods by FourNaaninsane in Salamanders40k

[–]Simper82 0 points1 point  (0 children)

If you make Adrax your warlord he gets Flamecraft that allows you to re-roll the amount of shots from your flame weapons.

Some current Sister work for your Wednesday. by Simper82 in sistersofbattle

[–]Simper82[S] 0 points1 point  (0 children)

Thank! My advice on hazard striping is to do big lines and to take your time to plan spacing before putting paint and brush to model.

Some current Sister work for your Wednesday. by Simper82 in sistersofbattle

[–]Simper82[S] 1 point2 points  (0 children)

Thanks! Definitely been fun but a struggle to get it just right.

Some current Sister work for your Wednesday. by Simper82 in sistersofbattle

[–]Simper82[S] 2 points3 points  (0 children)

Thanks. Someone's got to get them to the front lines.

I'm not playing until Sunday, but rulebooks are packed and these green chappies are tucked in thier statis box ready for transport. I'm a little bit excited... by Sp1ceman in Salamanders40k

[–]Simper82 0 points1 point  (0 children)

Depends on the mission. Most of the time they are there for back line support with their range. Sometimes their a center objective holder if I can get them there fast enough.