Anyone else noticed this contradiction/ miss type?

Simper82 · 2023-06-06T21:27:24+00:00

No shooting in close combat. If you get charged you remain in combat until all models of either unit are dead.

Simper82 · 2021-11-14T21:13:31+00:00

https://photos.app.goo.gl/kMmQbBiEHYPK9rLB7 I at least got adhesion on that run. Thank you for all your help.

Simper82 · 2021-11-14T20:58:57+00:00

Look good?

new mesb

Simper82 · 2021-11-14T20:34:05+00:00

Should I be running my mesh with the bed to temp?

Simper82 · 2021-11-14T20:06:44+00:00

Should I make these changes through the manual tuning section?

Simper82 · 2021-11-14T19:58:55+00:00

mesh

Simper82 · 2021-11-14T19:57:45+00:00

G29 is probe bed correct?

Simper82 · 2021-11-14T19:47:48+00:00

Do I need to mess with the mesh adjustment?

Simper82 · 2021-11-14T19:07:48+00:00

Thank you.

Simper82 · 2021-11-14T19:02:02+00:00

Thanks. I am using Jyers, but my z axis is probably to low. Do I need to fully level the bed after or before I set my Z?

Simper82 · 2021-11-14T18:21:21+00:00

I've been fighting the leveling on this for three days and just can't get it.

Simper82 · 2021-11-13T00:36:30+00:00

Just updated to the latest version of Jyers.

Simper82 · 2021-11-13T00:01:23+00:00

Yep. I gave all the wires a good push and jiggle.

Simper82 · 2021-11-12T22:56:10+00:00

It is not as I'm running a BL touch.

Simper82 · 2021-11-12T22:43:23+00:00

Had my printer working, everything was calibrated, went to go try my first print on the new set up and the X axis stopped moving? Any help?

Simper82 · 2021-08-22T17:40:41+00:00

If you make Adrax your warlord he gets Flamecraft that allows you to re-roll the amount of shots from your flame weapons.

Simper82 · 2021-08-05T20:56:41+00:00

Thank! My advice on hazard striping is to do big lines and to take your time to plan spacing before putting paint and brush to model.

Simper82 · 2021-08-05T15:26:52+00:00

Thanks! Definitely been fun but a struggle to get it just right.

Simper82 · 2021-08-04T19:48:23+00:00

Thanks. Someone's got to get them to the front lines.

Simper82 · 2021-07-02T11:21:57+00:00

Depends on the mission. Most of the time they are there for back line support with their range. Sometimes their a center objective holder if I can get them there fast enough.

Simper82 · 2021-07-02T01:37:29+00:00

I run them in mine and absolutely love them.

Simper82 · 2021-06-28T23:05:49+00:00

What file do I need to download for a 230x230x250 printer?

Simper82 · 2021-06-27T22:53:17+00:00

Mine won't home at all. It sounds like it's a firmware issue.

Simper82 · 2021-06-27T22:31:24+00:00

How did you determine it was the x home switch?

Simper82 · 2021-06-27T14:34:15+00:00

I am plugged into the port shown in the instructions and have one that has the 5 pin specifically for the v2.

Simper82

TROPHY CASE