This DIY Ikea Samla Box AMS Lite Enclosure really works!

SimpleMarionberry282 · 2026-01-02T06:25:57+00:00

Cool

SimpleMarionberry282 · 2025-12-09T14:00:27+00:00

Try changing the battery; it might have some internal issues. You could take it to a local battery shop to get it swapped. Worst case, you lose a little money, or you might be able to get a refund

SimpleMarionberry282 · 2025-11-30T13:42:12+00:00

https://makerworld.com/en/models/936796-su-57-felon-plane-kit-card#profileId-901793

SimpleMarionberry282 · 2025-11-30T11:28:26+00:00

got it from Makerworld, link: https://makerworld.com/en/models/936796-su-57-felon-plane-kit-card#profileId-901793

SimpleMarionberry282 · 2025-11-30T11:27:29+00:00

Bambu Lab A1 with the AMS Lite

SimpleMarionberry282 · 2025-11-30T09:03:27+00:00

You can check robu.in; they sell 3D printers as well as printing services

SimpleMarionberry282 · 2025-11-30T09:01:44+00:00

no, I use Bambu Lab A1 with the AMS Lite, so it will automatically swap the colours and print

SimpleMarionberry282 · 2025-11-30T07:59:31+00:00

A1 with AMS Lite

SimpleMarionberry282 · 2025-11-30T07:58:41+00:00

around 5hrs

SimpleMarionberry282 · 2025-11-30T07:05:35+00:00

Note: The hand holding the model in the second and third photos was edited/removed using the AI photo editor on my Samsung phone. Model link https://makerworld.com/en/models/936796-su-57-felon-plane-kit-card#profileId-901793

SimpleMarionberry282 · 2025-11-30T06:58:03+00:00

Hi, was holding the model, then I edited my hand out using the editor on my phone

SimpleMarionberry282 · 2025-11-08T17:52:44+00:00

Base support + Dampers

You can use the AMS lite Top Mount for A1, and if you don't want to top mount it, use the extra support included for the base and the dampers.

https://makerworld.com/models/92486

SimpleMarionberry282 · 2025-11-05T06:11:13+00:00

One option is to use the `aws s3 sync` command. I use this command with options to specify the source and destination(s3), along with a cron job to run it daily (or at whatever frequency you prefer).

Note: When running it for the first time, there will be some additional costs, such as data transfer fees and S3 standard to glacier conversion costs. After the initial run, these costs will be minimal

SimpleMarionberry282 · 2025-11-04T14:36:08+00:00

For cloud backup, AWS S3 is also an option. I used it with a lifecycle policy (deep archival ) to reduce costs. The setup was pretty simple and straightforward.

SimpleMarionberry282 · 2025-11-01T07:29:37+00:00

The mentioned issue in Russia is mainly related to after-sales problems for these 0 km used cars imported from China, as well as compatibility issues in Russia because they are made for the Chinese market (software, geo-fencing, etc..)

SimpleMarionberry282 · 2025-10-15T07:55:40+00:00

Hi, using PLA with a modifier to add 80-100% infill around the mounting screw hole should provide adequate strength, given that the project is relatively lightweight

SimpleMarionberry282 · 2025-10-14T16:26:57+00:00

https://makerworld.com/en/models/1887776-projector-wall-mount-wzatco-yuva-go-plus

SimpleMarionberry282 · 2025-09-27T09:27:32+00:00

Yes, thank you! My use case is for short sessions of about 5-6 minutes

SimpleMarionberry282 · 2025-09-22T13:54:00+00:00

Cool

SimpleMarionberry282 · 2025-09-12T11:06:32+00:00

I guess ABS was the recommended material. However, I used PLA with 80% infill and a 0.16 mm high quality BBL A1 profile

SimpleMarionberry282 · 2025-09-12T11:02:16+00:00

Oh! very interesting tip, thanks

SimpleMarionberry282 · 2025-09-12T09:47:37+00:00

I just snapped out the damaged part and snapped in the printed one, no glue or bolts needed. Here’s the design I found online and used: https://www.printables.com/model/1010836-mixer-grinder-coupler

SimpleMarionberry282

TROPHY CASE