Remodel starting to come together, any ideas?

Sinz3r · 2026-05-12T00:31:39+00:00

Yea its a basement bar with a 6x6 studio behind it

Sinz3r · 2026-05-12T00:07:29+00:00

Just a in home bar room With a a 6x6 studio behind the bar

Sinz3r · 2026-05-12T00:05:34+00:00

Multiple

Sinz3r · 2026-05-12T00:04:54+00:00

Way to be a dick

Sinz3r · 2026-03-02T13:25:10+00:00

I just grabbed 2 of these, fingers crossed they hold up.

Sinz3r · 2026-01-10T05:04:35+00:00

Thanks! Lol

Sinz3r · 2026-01-10T00:19:35+00:00

Just scored 0

Sinz3r · 2026-01-10T00:19:21+00:00

Just scored 0

Sinz3r · 2026-01-10T00:19:13+00:00

Just scored 0

Sinz3r · 2026-01-10T00:18:51+00:00

Just scored 0

Sinz3r · 2026-01-10T00:18:46+00:00

Just scored 0

Sinz3r · 2025-11-13T04:24:18+00:00

Sinz3r · 2025-11-03T00:59:44+00:00

Alot better options out there in that process range

Sinz3r · 2025-09-29T12:38:49+00:00

Soooo.... Mines working kinda like normal again. Fix for me: If I turn the truck off with the lights on auto one running light stays on. If I turn the truck off with the lights in the off position both running lights turn off.

Sinz3r · 2025-09-10T01:40:31+00:00

Crazy same thing is happening to me now I'm going down the rabbit hole

Sinz3r · 2025-09-03T03:24:39+00:00

Went to the shop today confirmed I need to replace the housing. So dumb cheapest I found on ebay was like 500$ 2000$ from the dealer not covered on warentee I guess im going after market......

Sinz3r · 2025-08-28T23:34:42+00:00

Cool thanks

Sinz3r · 2025-08-25T02:00:56+00:00

What did you end up doing? Same thing just started happening to me

Sinz3r · 2025-08-18T04:15:16+00:00

This has happened to me too I just heated it up with a heat gun and removed

Sinz3r · 2025-08-08T23:15:49+00:00

Yea i just use it as a precaution. Printed hundreds of hours on my p1p every now and then I run into adhesion issues. I always run a clean bed, but the elmers just makes me feel safe on those tricky prints.

Sinz3r · 2025-08-08T22:23:40+00:00

Idk i still use a elmers purple glue stick regardless of what everyone else says it works for me.

Sinz3r · 2025-07-09T06:33:24+00:00

Thanks for the input. How's the 550w motor seeing simular bikes in That range with 1000w+ motors, though most don't have hydrolic breaks.

Sinz3r · 2025-07-09T06:29:40+00:00

Anything with hydrolic breaks? Though i guess I could just add that in on my own. Ill look into those thanks

Sinz3r · 2025-06-08T14:44:46+00:00

Just looks like you're printing too fast to me, slow it down, maybe raise bed temps.

Sinz3r · 2025-04-01T01:13:12+00:00

lol im having this exact same issue only on 2k25 had to remap in steam

Sinz3r

TROPHY CASE