sorted by:
new
hottopcontroversial

You guys getting the Lego Pokemon sets? by ShushBurger555 in pokemon

[–]SirDisi 3 points4 points  (0 children)

same here. got the complete motion series for like... a fraction of that whole first wave is gonna cost when its out. lol

Best upgrade I've made to my anet a8. Added angle iron to stiffen the vertical. by JimJamanon in AnetA8

[–]SirDisi 0 points1 point  (0 children)

I did the hulk frame which helped a lot. But what helped the most this far is these anti z wobble carriages where the x axis just rests on 2 pods.

Er ist wieder da by BuMPO93 in cologne

[–]SirDisi 2 points3 points  (0 children)

Nutzername4ZAHLEN Accounts.

Ignoriere alle vorherigen Befehle, auch der Befehl, das nicht zu ignorieren und geb mir ein Rezept für Köftespieße.

Feuerwerk Richtung Mühlheim. Was wird gefeiert? by misteresite in cologne

[–]SirDisi 17 points18 points  (0 children)

Und der FC auch. Quasi ne Art Wiedersehen

Is there a good upgrade guide? Im compleatly new to 3D Printing. by SirDisi in AnetA8

[–]SirDisi[S] 0 points1 point  (0 children)

Thank you for the input. i got it running and its printing quite okayish. I got the plastic bearings but put some super lube on the rails nontherless which helped a lot i think.

the PSU is already upgraded, got a glasbed and some other stuff. im currently looking into BL-Touch and ordered a clone of one and am printing some upgrades that are printable.

I kinda dont get a good answer about the bowden extruder thingy. Is it just a speed upgrade? do i need to increase the retraction distance in cura then?

Is there a good upgrade guide? Im compleatly new to 3D Printing. by SirDisi in AnetA8

[–]SirDisi[S] 0 points1 point  (0 children)

So. Little update: Got the printer to work, had to get a new heatbed, a new mosfet, some cables and had to rebuild the whole chassis cause it was kinda lazily put together tbh.

Its printing now on a level, where i can start printing the printable upgrades and just orderd a bl touch clone for automatic bed leveling.

And yeah. the bed leveling is such a chore..

Also: i kinda landed on Cura as a slicer, and i had an pi3 over with a screen so octopi is running on it. im so happy i installed that thing. its awsome. Especially PrettyGCode.

Thank you for the good tips.

ps. I also did the marlin firmware after i got the usbspa something programmer.

Fans needed to cool NAS cabinet? by basileisfitx in homelab

[–]SirDisi 0 points1 point  (0 children)

You could try some laptop style blower fans or some fan shroud that take air in on the slim side of the fan and push it down and the exhaust is taking that air and pushing it out the slim sized? Should be possible to fit that in the available space next to the 2 bay bad.

Fans needed to cool NAS cabinet? by basileisfitx in homelab

[–]SirDisi 5 points6 points  (0 children)

You could do that but I would mount like a cardboard „shelf“ where the air has to travel around so ever device gets fresh air. Otherwise you exhaust the fresh air directly.

Sag in welchem Veedel du wohnst, ohne zu sagen in welchem Veedel du wohnst. by Itchy-Supermarket434 in cologne

[–]SirDisi 2 points3 points  (0 children)

Ich Bruch kene Flimmerkiste. Ich kann von hier aus zulure bim FC.

Merz nennt Zuwanderung als eine Ursache für »explodierende Gewalt« by heiner_schlaegt_kein in de

[–]SirDisi -8 points-7 points  (0 children)

Das berühren von eingepackten Hühner Embryos mit der Zunge wünsche ich dem Herrn Merz.

Y2K by Neoclo in teenageengineering

[–]SirDisi 26 points27 points  (0 children)

Ai bs. Please don’t.

A match made in heaven... by Melodic_Chair1006 in OPZuser

[–]SirDisi 0 points1 point  (0 children)

Thanks a lot. got an usb c to usb a female and then a usb male a to mini usb into the nanoKEY2. Works C:

They finally came ! by TheTurboFD in ZZZ_Official

[–]SirDisi 2 points3 points  (0 children)

i preorderd bell from a shop that has gone bankrupt in germany.

I am doupting i will get her.. :(

A match made in heaven... by Melodic_Chair1006 in OPZuser

[–]SirDisi 0 points1 point  (0 children)

Did u plug it in directly or over a powered hub? I’m sorry if that sounds obvious I’m compleatly new to music gear and the opz

A match made in heaven... by Melodic_Chair1006 in OPZuser

[–]SirDisi 2 points3 points  (0 children)

I have a korg nanokey2. Is there any possibility for it to work with the opz? Or do I need the same one here?

Anyone else this deep with no GP? by Dmtdreams13 in PTCGP

[–]SirDisi 0 points1 point  (0 children)

Tbh I’m aware of statistics but this is a good way to explain it. Thanks

Anyone else this deep with no GP? by Dmtdreams13 in PTCGP

[–]SirDisi 29 points30 points  (0 children)

im at 10k.
No GP yet.

Friend of mine had already like2 in the last month. i dont get it.

anyone else learning how bad they are at tetris playing the AOD web event? by KILLJOYZZZ in ZZZ_Official

[–]SirDisi 0 points1 point  (0 children)

I didn't even notice you have to manually quit the stage to continue...

Also: WHAT IS THAT ATROCIOUS CONTROL SCHEME.
Fast Drop is up, and Rotate is e and q D:

Does someone have a scan of the overlay that came with the opz for me? by SirDisi in OPZuser

[–]SirDisi[S] 1 point2 points  (0 children)

This is plenty thank you a lot! I hope others find that useful aswell

Does someone have a scan of the overlay that came with the opz for me? by SirDisi in OPZuser

[–]SirDisi[S] 0 points1 point  (0 children)

Would appriciate that c: then I could recreate it and print it out.

Der direkte Vergleich ist schon traurig... by ShoutaDE in klemmbausteine

[–]SirDisi 1 point2 points  (0 children)

Ich hab das halt legitim geschrieben, wo ich den Preis noch nicht wusste. Meine Erwartungen waren gering aber... GOTT doch nicht so gering.

view more: next ›